Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2001 Chrysler Voyager Base, 2.4 BFACTORY OEM SERVICE PROCEDURE
Incomplete Power Open - Overcurrent
NOTE:
After making any repairs, perform BODY VERIFICATION TESTΒ
under VERIFICATION TESTS.
- Using scan tool, record and erase DTCs. Turn ignition off. Wait 10 seconds. Turn ignition on. Operate power liftgate several times if possible. Recheck for DTCs. If INCOMPLETE POWER OPEN - OVER CURRENT resets, go to next step. If INCOMPLETE POWER OPEN - OVER CURRENT T does not reset, system is operating properly at this time. Check for intermittent poor connections or faulty circuits.
- Visually inspect liftgate for proper alignment, damaged strikers, damaged latches or obstructions. Repair as necessary. If possible, check operation of liftgate on a known-good vehicle. If liftgate effort is excessive, diagnose power liftgate by symptom. See TROUBLE SHOOTING in POWER SLIDING DOORS & LIFTGATE - CARAVAN, TOWN & COUNTRY, & VOYAGER article. If liftgate effort is not excessive, go to next step.
- Turn ignition off. Disconnect Power Liftgate Module (PLGM) connector C1. See Figure . To access connector, left rear trim will need to be removed. See POWER LIFTGATE MODULEΒ under REMOVAL & INSTALLATION. Using a test light connected to battery voltage, probe PLGM connector C1 terminal No. 8 (Black/White wire). See Figure . If test light illuminates brightly, go to next step. If test light does not illuminate or is dim, repair open or high resistance in Black/White wire between PLGM and ground connection located in left rear corner of vehicle.
- Disconnect PLGM connector C2. Disconnect liftgate cinch/release motor connector. See Figure . To access connector, door panel will need to be removed. For removal and installation procedures, see POWER SLIDING DOOR MODULEΒ under REMOVAL & INSTALLATION. Using DVOM, measure resistance of Tan/Gray wire between PLGM connector C2 terminal No. 8 and liftgate cinch/release motor connector terminal No. 6. Wiggle wiring harness with DVOM connected. If resistance is steady at 5 ohms or less, go to next step. If resistance is greater than 5 ohms or varies, repair open in Tan/Gray wire.
- Using DVOM, measure resistance between ground and PLGM connector C2 terminal No. 8 (Tan/Gray wire). Wiggle wiring harness with DVOM connected. If resistance is greater than 100 ohms and steady, go to next step. If resistance is 100 ohms or less or varies, repair short to ground in Tan/Gray wire between PLGM and liftgate cinch/release motor connector terminal No. 6. See Figure .
- Using DVOM, measure resistance between PLGM connector C2 terminals No. 8 (Tan/Gray wire) and No. 20 (Black/Light Green wire). Wiggle wiring harness with DVOM connected. If resistance is greater than 1000 ohms and steady, go to next step. If resistance is 1000 ohms or less or varies, repair short between Tan/Gray and Black/Light Green wires. See WIRING DIAGRAMS in POWER SLIDING DOORS & LIFTGATE - CARAVAN, TOWN & COUNTRY, & VOYAGER article.
- Disconnect power liftgate motor connector. Using DVOM, measure resistance between ground and PLGM connector C2 terminal No. 7 (Orange/Dark Blue wire). Wiggle wiring harness with DVOM connected. If resistance is greater than 1000 ohms and steady, go to next step. If resistance is 1000 ohms or less or varies, repair short to ground in Orange/Dark Blue wire between PLGM and power liftgate motor connector terminal No. 5.
- Using DVOM, measure resistance between PLGM connector C2 terminals No. 7 (Orange/Dark Blue wire) and No. 20 (Black/Light Green wire). Wiggle wiring harness with DVOM connected. If resistance is greater than 1000 ohms and steady, replace liftgate cinch/release motor assembly. If resistance is 1000 ohms or less or varies, repair short between Orange/Dark Blue and Black/Light Green wires.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
