Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2001 Chrysler Intrepid BaseFACTORY OEM SERVICE PROCEDURE
Passenger Heated Seat Switch Open/Shorted To Ground
NOTE:
After making any repairs, perform MEMORY SYSTEMS VERIFICATION TESTΒ
under VERIFICATION TESTS.
- Turn ignition off. Connect scan tool to Data Link Connector (DLC). Turn ignition on. Using scan tool, select BODY MEMORY SEAT MODULE, then retrieve DTCs. If any Memory Heated Seat/Mirror Module (MHSMM) DTCs are present, go to next step. If no MHSMM DTCs are present, go to step Β 3 .
- Using scan tool, clear MHSMM DTCs. Start engine and allow it to run for one minute while operating heated seat switch. Using scan tool retrieve MHSMM DTCs. If PASSENGER HEATED SEAT SWITCH OPEN/SHORTED TO GROUND DTC resets, go to step Β 4 . If PASSENGER HEATED SEAT SWITCH OPEN/SHORTED TO GROUND DTC does not reset, fault may be intermittent. Check related wiring and connectors for poor connections or damage to wiring harness. See WIRING DIAGRAMSΒ . Repair any problems found as necessary. If no problems are found, check if any Technical Service Bulletins (TSBs) apply to vehicle. If no TSBs apply, test is complete.
- Turn ignition off. Disconnect passenger heated seat switch connector. Turn ignition on. Measure voltage on passenger heated seat switch connector terminal No. 4, fused ignition switch output circuit (Dark Blue/White wire). See Figure . If voltage is more than 10 volts, go to next step. If voltage is 10 volts or less, repair open in Dark Blue/White wire.
- Turn ignition off. Disconnect MHSMM connector C1. Turn ignition on. Measure voltage between ground and MHSMM connector C1 terminal No. 5, passenger seat heater switch MUX circuit (Tan/Light Green wire). See Figure . If voltage is more than 10 volts, replace MHSMM. If voltage is 10 volts or less, leave MHSMM connector C1 disconnected, and go to next step.
- Turn ignition off. Disconnect passenger heated seat switch connector. Measure resistance of passenger seat heater switch MUX circuit (Tan/Light Green wire) between passenger heated seat switch connector terminal No. 6 and MHSMM connector C1 terminal No. 5. See Figure and Figure . If resistance is less than 5 ohms, leave connectors disconnected, and go to next step. If resistance is 5 ohms or more, repair open in Tan/Light Green wire.
- Measure resistance between ground and MHSMM connector C1 terminal No. 5, passenger seat heater switch MUX circuit (Tan/Light Green wire). If resistance is less than 100 ohms, repair short to ground in Tan/Light Green wire. If resistance is 100 ohms or more, replace passenger heated seat switch.
NOTE:
Cycling ignition switch with Ignition Off-Draw (IOD) fuse removed, may set this DTC. IOD fuse is located in Power Distribution Center (PDC). Fuses are identified on label located inside PDC cover.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
