Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2000 Chrysler Intrepid (CANADA) V6-3.2LFACTORY OEM SERVICE PROCEDURE
Front Cross-Member: Service and Repair
ENGINE CRADLE CROSSMEMBER
REMOVAL
CAUTION: VERIFY THAT VEHICLE IS PROPERLY SUPPORTED AND SECURED TO THE LIFTING DEVICE. VEHICLE CENTER OF GRAVITY WILL CHANGE WHEN HEAVY COMPONENTS ARE REMOVED CAUSING A HAZARDOUS CONDITION.
1. Release hood latch and open hood.
2. Remove nuts holding engine mounts to cradle.
3. Install a suitable engine support device.
4. Raise and support vehicle on safety stands.
5. Remove bolts holding transaxle crossmember to cradle.
6. Lower vehicle and lift engine and transaxle off cradle.
7. Raise and support vehicle on safety stands.
8. Disconnect sway bar links.
9. Remove bolts retaining suspension lower ball joints to spindles.
10. Separate lower control arm from spindle.
11. Support cradle on a 10 cm by 10 cm by 90 cm (4 in. by 4 in. by 36 in.) wood beam and a jack.

12. Remove bolts holding cradle to body shell (Fig. 15).
13. Lower cradle away from body shell.
INSTALLATION
NOTE: If cradle replacement is required, transfer suspension components and jounce and bounce plates to replacement cradle.
1. Support cradle on wood beam and a jack.
2. Position cradle under body shell.
3. Install bolts to hold cradle to body shell.
4. Connect lower control arms to spindles
5. Install bolts to retain suspension lower ball joints to spindles.
6. Connect sway bar links.
7. Lower vehicle and lower engine and transaxle onto cradle.
8. Raise vehicle.
9. Install bolts to hold transaxle crossmember to cradle.
10. Lower vehicle.
11. Remove engine support device.
12. Install nuts to hold engine mounts to cradle.
13. Align front suspension if necessary.
REMOVAL
CAUTION: VERIFY THAT VEHICLE IS PROPERLY SUPPORTED AND SECURED TO THE LIFTING DEVICE. VEHICLE CENTER OF GRAVITY WILL CHANGE WHEN HEAVY COMPONENTS ARE REMOVED CAUSING A HAZARDOUS CONDITION.
1. Release hood latch and open hood.
2. Remove nuts holding engine mounts to cradle.
3. Install a suitable engine support device.
4. Raise and support vehicle on safety stands.
5. Remove bolts holding transaxle crossmember to cradle.
6. Lower vehicle and lift engine and transaxle off cradle.
7. Raise and support vehicle on safety stands.
8. Disconnect sway bar links.
9. Remove bolts retaining suspension lower ball joints to spindles.
10. Separate lower control arm from spindle.
11. Support cradle on a 10 cm by 10 cm by 90 cm (4 in. by 4 in. by 36 in.) wood beam and a jack.
Fig. 15:
12. Remove bolts holding cradle to body shell (Fig. 15).
13. Lower cradle away from body shell.
INSTALLATION
NOTE: If cradle replacement is required, transfer suspension components and jounce and bounce plates to replacement cradle.
1. Support cradle on wood beam and a jack.
2. Position cradle under body shell.
3. Install bolts to hold cradle to body shell.
4. Connect lower control arms to spindles
5. Install bolts to retain suspension lower ball joints to spindles.
6. Connect sway bar links.
7. Lower vehicle and lower engine and transaxle onto cradle.
8. Raise vehicle.
9. Install bolts to hold transaxle crossmember to cradle.
10. Lower vehicle.
11. Remove engine support device.
12. Install nuts to hold engine mounts to cradle.
13. Align front suspension if necessary.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
