2025 Chevrolet Trax LSFACTORY OEM SERVICE PROCEDURE

Fastener Specifications

GM5950064Courtesy of GENERAL MOTORS COMPANY
Accelerator Pedal Assembly

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Accelerator Pedal Assembly Bolt - - 6 N.m (53 lb in) Accelerator Pedal Assembly Replacement
GM6196341Courtesy of GENERAL MOTORS COMPANY
Air Cleaner Assembly with Mass Airflow Sensor

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Air Cleaner Outlet Duct Clamp - - 3 N.m (27 lb in) Air Cleaner Outlet Rear Duct Replacement
2 Air Cleaner Clamp - - 3 N.m (27 lb in) Air Cleaner Outlet Rear Duct Replacement
3 Mass Airflow Sensor Bolt [2x] - - 1.3 N.m (12 lb in) Mass Airflow Sensor Replacement
4 Air Cleaner Housing Cover Bolt [4x] - - 1.6 N.m (14 lb in) Air Cleaner Element Replacement
GM6196342Courtesy of GENERAL MOTORS COMPANY
Camshaft Position Actuator Solenoid Valve & Engine Control Module Bracket

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Camshaft Position Actuator Solenoid Valve Bolt [4x] - - 8.5 N.m (75 lb in) Camshaft Position Actuator Solenoid Valve Replacement - Intake
Camshaft Position Actuator Solenoid Valve Replacement - Exhaust
2 Camshaft Position Actuator Magnet Gasket [2x] Yes - - Camshaft Position Actuator Solenoid Valve Replacement - Intake
Camshaft Position Actuator Solenoid Valve Replacement - Exhaust
3 Engine Control Module Bracket Bolt [3x] - - 9 N.m (80 lb in) Engine Control Module Bracket Replacement
GM6196343Courtesy of GENERAL MOTORS COMPANY
Camshaft Position Sensor

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Camshaft Position Sensor Bolt [2x] - - 8.5 N.m (75 lb in) Camshaft Position Sensor Replacement - Intake
Camshaft Position Sensor Replacement - Exhaust
GM6196344Courtesy of GENERAL MOTORS COMPANY
Charge Air Cooler

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Charge Air Cooler Bolt [2x] - - 3 N.m (27 lb in) Charge Air Cooler Replacement
GM6178546Courtesy of GENERAL MOTORS COMPANY
Charge Air Cooler Inlet Air Hose

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Charge Air Cooler Inlet Air Hose Clamp Nut - - 6 N.m (53 lb in) Charge Air Cooler Inlet Air Hose Replacement
GM6196345Courtesy of GENERAL MOTORS COMPANY
Crankcase Pressure Sensor & Evaporative Emission Canister Purge Solenoid Valve & Turbocharger Bypass Valve Solenoid & Vacuum Pump

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Crankcase Pressure Sensor Bolt - - 8.5 N.m (75 lb in) Crankcase Pressure Sensor Replacement
2 Evaporative Emission Canister Purge Solenoid Valve Bolt - - 8.5 N.m (75 lb in) Evaporative Emission Canister Purge Solenoid Valve Replacement
3 Turbocharger Bypass Valve Solenoid Bolt [3x] - - 7 N.m (62 lb in) Turbocharger Bypass Valve Solenoid Replacement
4 Vacuum Pump Bolt [3x] - - 15 N.m (11 lb ft) Vacuum Pump Replacement
5 Vacuum Pump Gasket Yes - - Vacuum Pump Replacement
GM6196346Courtesy of GENERAL MOTORS COMPANY
Crankshaft Position Sensor & Engine Oil Pressure Sensor & Knock Sensor & Oil Pump Flow Control Solenoid Valve

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Knock Sensor Bolt - - 15 N.m (11 lb ft) Knock Sensor Replacement
2 Engine Oil Pressure Sensor - - 35 N.m (26 lb ft) Engine Oil Pressure Sensor Replacement
3 Crankshaft Position Sensor Bolt - - 8.5 N.m (75 lb in) Crankshaft Position Sensor Replacement (KL9) , or Crankshaft Position Sensor Replacement (- KL9)
4 Oil Pump Flow Control Solenoid Valve Bolt - - 8.5 N.m (75 lb in) Oil Pump Flow Control Solenoid Valve Replacement
5 Oil Pump Flow Control Solenoid Valve Seal Yes - - Oil Pump Flow Control Solenoid Valve Replacement
GM6196347Courtesy of GENERAL MOTORS COMPANY
Direct Fuel Injection Fuel Rail & Fuel Rail Pressure Sensor

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Fuel Injection Fuel Rail Bolt [4x] - - Fuel Injection Fuel Rail Bolt Sequence  Direct Fuel Injection Fuel Rail Replacement
2 Fuel Rail Pressure Sensor - - 32.5 N.m (24 lb ft) Fuel Rail Pressure Sensor Replacement
GM6196348Courtesy of GENERAL MOTORS COMPANY
Evaporative Emission Canister Purge Pump & Intake Air Pressure and Temperature Sensor & Throttle Body Assembly & Turbocharger Wastegate Regulator Solenoid Valve

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Evaporative Emission Canister Purge Pump Bolt [2x] - - 8.5 N.m (75 lb in) Evaporative Emission Canister Purge Pump Replacement (With Bracket) , or Evaporative Emission Canister Purge Pump Replacement (Without Bracket)
2 Intake Air Pressure and Temperature Sensor Bolt - - 8.5 N.m (75 lb in) Intake Air Pressure and Temperature Sensor Replacement
3 Turbocharger Wastegate Regulator Solenoid Valve Bolt [2x] - - 15 N.m (11 lb ft) Turbocharger Wastegate Regulator Solenoid Valve Replacement
4 Throttle Body Assembly Bolt [3x] - - 8.5 N.m (75 lb in) Throttle Body and Throttle Body Adapter Assembly Replacement
5 Throttle Body Seal [2x] Yes - - Throttle Body and Throttle Body Adapter Assembly Replacement
GM6473019Courtesy of GENERAL MOTORS COMPANY
Evaporative Emission Canister Purge Pump Bracket

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Evaporative Emission Canister Purge Pump Bolt [3x] - - 1.8 N.m (16 lb in) Evaporative Emission Canister Purge Pump Bracket Replacement
GM6557298Courtesy of GENERAL MOTORS COMPANY
Evaporative Emission System Vacuum Leak Detection Pump

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Evaporative Emission System Vacuum Leak Pump Nut [3x] - - 4.2 N.m (37 lb in) Evaporative Emission System Vacuum Leak Detection Pump Replacement (LBP)
GM6557299Courtesy of GENERAL MOTORS COMPANY
Evaporative Emission System Vacuum Leak Pump Bracket

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Evaporative Emission Canister Filter Bracket Nut [3x] - - 9 N.m (80 lb in) Evaporative Emission System Vacuum Leak Pump Bracket Replacement (LBP)
GM6196349Courtesy of GENERAL MOTORS COMPANY
Fuel Feed Intermediate Pipe & Fuel Pump & Fuel Pump Cover

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Fuel Feed Intermediate Pipe Bolt - - 8.5 N.m (75 lb in) Fuel Feed Intermediate Pipe Replacement (LBP)
2 Fuel Feed Intermediate Pipe Yes - 30 N.m (22 lb ft) Fuel Feed Intermediate Pipe Replacement (LBP)
3 Fuel Pump Shield Bolt [3x] - - 8.5 N.m (75 lb in) Fuel Pump Cover Replacement
4 Fuel Pump Bolt [2x] - - 36 N.m (27 lb ft) Fuel Pump Replacement
5 Fuel Pump Housing Seal Yes - - Fuel Pump Replacement
GM6196350Courtesy of GENERAL MOTORS COMPANY
Fuel Tank Shield & Fuel Tank Strap

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Fuel Tank Shield Nut [3x] - - 2 N.m (18 lb in) Fuel Tank Shield Replacement
2 Fuel Tank Strap Bolt [4x] - - 22 N.m (16 lb ft) Fuel Tank Replacement (LBP)
GM6196351Courtesy of GENERAL MOTORS COMPANY
Fuel Pump Power Control Module & Fuel Tank Filler Pipe & Fuel Tank Filler Hose

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Fuel Tank Filler Pipe Bolt [2x] - - 9 N.m (80 lb in) Fuel Tank Filler Pipe Replacement
2 Fuel Pump Power Control Module Nut [2x] - - 5 N.m (44 lb in) Fuel Pump Power Control Module Replacement (LBP)
3 Fuel Tank Filler Hose Clamp [2x] - - 5 N.m (44 lb in) Fuel Tank Filler Hose Replacement
GM6196352Courtesy of GENERAL MOTORS COMPANY
Heated Oxygen Sensor

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Heated Oxygen Sensor-Sensor 1 - - 42 N.m (31 lb ft) Heated Oxygen Sensor Replacement - Sensor 1
2 Heated Oxygen Sensor-Sensor 2 - - 42 N.m (31 lb ft) Heated Oxygen Sensor Replacement - Sensor 2
GM6196353Courtesy of GENERAL MOTORS COMPANY
Ignition Coil & Gas Engine Ignition Spark Plug

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Ignition Coil Bolt [6x] - - 8.5 N.m (75 lb in) Ignition Coil Replacement
2 Gas Engine Ignition Spark Plug [3x] - - 16 N.m (12 lb ft) Gas Engine Ignition Spark Plug Replacement
GM6196354Courtesy of GENERAL MOTORS COMPANY
Throttle Inlet Absolute Pressure Sensor

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Throttle Inlet Absolute Pressure Sensor Bolt - - 3 N.m (27 lb in) Throttle Inlet Absolute Pressure Sensor Replacement
Fuel Injection Fuel Rail Bolt Sequence
GM5389552Courtesy of GENERAL MOTORS COMPANY
Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Fuel Injection Fuel Rail Bolt [4x] - - 36 N.m (27 lb ft) Direct Fuel Injection Fuel Rail Replacement
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.