2025 Chevrolet Trax LSFACTORY OEM SERVICE PROCEDURE

Removal Procedure

  1. Open the liftgate.
  2. GM6275451Courtesy of GENERAL MOTORS COMPANY

    Load Floor Mat (1) - Remove

  3. GM6306918Courtesy of GENERAL MOTORS COMPANY

    Load Floor Stowage Compartment Cover (1) - Remove

  4. GM5920420Courtesy of GENERAL MOTORS COMPANY

    Grasp and gently pull up on the liftgate sill garnish molding (1) in order to release the integral retaining clips.

  5. Liftgate Sill Garnish Molding (1) - Remove
  6. GM5922142Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Both sides shown. The quantity is for the one side.

    Cargo Tie Down Loop Fastener - Right Side (1) - Remove

  7. Cargo Tie Down Loop - Right Side (2) - Remove
  8. GM5922146Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Left side shown, right side similar.

    Rear Compartment Courtesy Lamp - Right Side (1) - Remove

  9. Disconnect the electrical connector.
  10. GM5922135Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Left side shown, right side similar.

    Use a flat-bladed tool to open the quarter window trim finish panel bolt cap.

  11. Quarter Window Trim Finish Panel Bolt - Right Side (1) - Remove
  12. Body Lock Pillar Upper Trim Panel - Right Side (2) - Remove
    1. Use a flat bladed plastic trim tool.
    2. Grasp and gently pull up on the body lock pillar upper trim panel.
  13. GM6273928Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Left side shown, right side similar.

    Rear Compartment Panel Bolt - Right Side (1) - Remove [2x]

  14. Cargo Partition Rail Bracket - Right Side (2) - Remove
  15. GM6273929Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Left side shown, right side similar.

    Rear Compartment Panel Bolt - Right Side (1) - Remove [2x]

  16. Rear Compartment Panel Reinforcement - Right Side (2) - Remove
  17. GM6307802Courtesy of GENERAL MOTORS COMPANY

    Load Floor Rear Compartment Cover (1) - Remove

  18. GM6307819Courtesy of GENERAL MOTORS COMPANY

    Cargo Tie Down Loop Fastener (1) - Remove [2x]

  19. Cargo Tie Down Loop (2) - Remove [2x]
  20. GM6307827Courtesy of GENERAL MOTORS COMPANY

    Rear Compartment Floor Stowage Compartment Bracket Bolt (1) - Remove [6x]

  21. Load Floor Trim Panel (2) - Remove
  22. GM5921871Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Left side shown, right side similar.

    Rear Side Door Sill Garnish Molding - Right Side (1) - Remove

    1. Starting at the front of the sill garnish molding, pull upward at the B-Pillar joint to disengage sill garnish molding.
    2. Work your way rearward disengaging all of the garnish molding clips then pull forward to disengage from the C-Pillar lower.
    3. Replace the retainers as required.
  23. GM5922859Courtesy of GENERAL MOTORS COMPANY

    Quarter Lower Rear Trim Panel (1) - Remove

    1. Release the retainers with a suitable plastic trim tool.
    2. Grasp and gently pull up on the quarter lower rear trim panel.
  24. Transfer components as necessary.
  25. GM5937799Courtesy of GENERAL MOTORS COMPANY

    Disconnect the electrical connectors.

  26. Remote Function Actuator Module (1) - Remove
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.