2021 Chevrolet Traverse LFACTORY OEM SERVICE PROCEDURE

Fastener Specifications

WARNING: This page is about a different car, the 2020 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
GM5504064Courtesy of GENERAL MOTORS COMPANY
Front Side Door Latch

Callout Component Name [ Component Quantity ] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Front Side Door Latch Bolt [ 4x ] - - 9 (80 lb in) Front Side Door Latch Replacement 
GM5504186Courtesy of GENERAL MOTORS COMPANY
Front Side Door Latch Striker

Callout Component Name [ Component Quantity ] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Front Side Door Latch Striker Bolt [ 2x ] - - 22 (16 lb ft) Front Side Door Latch Striker Replacement 
GM5504487Courtesy of GENERAL MOTORS COMPANY
Front Side Door Lock Cylinder Bezel

Callout Component Name [ Component Quantity ] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Front Side Door Lock Cylinder Bezel Bolt - - 4 (35 lb in) Front Side Door Lock Cylinder Bezel Replacement 
GM5442374Courtesy of GENERAL MOTORS COMPANY
Front Side Door Outside Handle Bracket

Callout Component Name [ Component Quantity ] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Front Side Door Outside Handle Bracket Bolt - - 4.7 (42 lb in) Front Side Door Outside Handle Bracket Replacement 
GM5504526Courtesy of GENERAL MOTORS COMPANY
Rear Compartment Lid Latch

Callout Component Name [ Component Quantity ] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Rear Compartment Lid Latch Bolt [ 2x ] - - 9 (80 lb in) Rear Compartment Lid Latch Replacement 
GM5504323Courtesy of GENERAL MOTORS COMPANY
Rear Compartment Lid Latch Striker

Callout Component Name [ Component Quantity ] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Rear Compartment Lid Latch Striker Bolt [ 2x ] - - 22 (16 lb ft) Rear Compartment Lid Latch Striker Replacement 
GM5507432Courtesy of GENERAL MOTORS COMPANY
Rear Side Door Latch

Callout Component Name [ Component Quantity ] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Rear Side Door Latch Bolt [ 4x ] - - 9 (80 lb in) Rear Side Door Latch Replacement 
GM5504343Courtesy of GENERAL MOTORS COMPANY
Rear Side Door Latch Striker

Callout Component Name [ Component Quantity ] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Rear Side Door Latch Striker Bolt [ 2x ] - - 22 (16 lb ft) Rear Side Door Latch Striker Replacement 
GM5507300Courtesy of GENERAL MOTORS COMPANY
Rear Side Door Lock Cylinder Opening Cover

Callout Component Name [ Component Quantity ] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Rear Side Door Lock Cylinder Opening Cover Bolt - - 4 (35 lb in) Rear Side Door Lock Cylinder Opening Cover Replacement 
GM5445334Courtesy of GENERAL MOTORS COMPANY
Rear Side Door Outside Handle Bracket

Callout Component Name [ Component Quantity ] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure
Metric (English)
1 Rear Side Door Outside Handle Bracket Bolt - - 4.7 (42 lb in) Rear Side Door Outside Handle Bracket Replacement 
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.