2021 Chevrolet Camaro LS, Automatic TransFACTORY OEM SERVICE PROCEDURE

Fastener Specifications

Single Use Non-Threaded Fasteners/Components

NOTE:

All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal.Β 

Application
Transmission Fluid Cooler Pipe Fitting Retainer
Transmission Fluid Cooler Pipe Fitting Seal
Reusable Threaded Fastener Tightening Specifications

NOTE:

All fasteners listed in this table can be reused after removal.Β 

Application Specification
Metric (English)
Range Selector Lever Cable Heat Shield Bolt
(LT1 With M5U Only)
9 N.m (80 lb in)
Side Underbody Front Air Deflector Bolt (Pipe Retaining Point)
(LT1 With M5U or MM6)
(LT4 With MGL or MJK)
9 N.m (80 lb in)
Transmission Fluid Auxiliary Cooler Bracket Bolt
(LT1 With M5U or MM6)
(LT4 With MGL or MJK)
9 N.m (80 lb in)
Transmission Fluid Auxiliary Cooler Bracket Nut
(LT1 With M5U or MM6)
(LT4 With MGL or MJK)
9 N.m (80 lb in)
Transmission Fluid Cooler Pipe Bracket Bolt (Rear Differential Hose Bracket Retaining Point)
(LT1 With M5U or MM6, With KNR)
(LT4 With MGL or MJK, With KNR)
9 N.m (80 lb in)
Transmission Fluid Cooler Pipe Clip Bolt (Pipe Retaining Points Along Vehicle)
(LGX With M13, With 1LE Package)
(LGX With M5T, With V03)
(LGX With M5T, Without V03)
(LT1 With M5U or MM6)
(LT4 With MJK)
9 N.m (80 lb in)
Transmission Fluid Cooler Pipe Clip Bolt (Transmission Connection Interface)
(LGX With M5T, With V03)
(LGX With M5T, With V03)
(LT1 With M5U)
(LT4 With MJK)
(LTG With M5T)
22 N.m (16 lb ft)
Transmission Fluid Cooler Pipe Clip Bolt (Transmission -Right Side)
(LT1 With M5U)
(LT4 With MJK)
22 N.m (16 lb ft)
Transmission Fluid Cooler Pipe Fitting (Radiator Fitting)
(All Models)
20 N.m (15 lb ft)
Transmission Fluid Cooler Pipe Nut (Pipe Retaining Points Along Vehicle)
(LTG With M5T)
9 N.m (80 lb in)
Transmission Fluid Cooler Pipe Nut (At Transmission Bell housing)
(LT4 With MJK)
22 N.m (16 lb ft)
Transmission Fluid Cooler Pipe Stud (Pipe Retaining Point)
(LGX With M13, With 1LE Package)
(LGX With M5T, Without V03)
(LTG With M5T)
22 N.m (16 lb ft)
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.