2020 Chevrolet Camaro SS, 2D Coupe, Standard TransFACTORY OEM SERVICE PROCEDURE

Circuit/System Testing

  1. Ignition OFF/vehicle OFF, disconnect the harness connector at the B24 Cellular Phone Microphone, ignition ON/vehicle in Service Mode.
  2. Test for 8.0-10.5 V between the signal circuit terminal B and ground.
    • If less than 8.0 V 
    1. Ignition OFF/vehicle OFF, disconnect the X2 harness connector at the K73 Telematics Communication Interface Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground in the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K73 Telematics Communication Interface Control Module.
    • If greater than 10.5 V 
    1. Ignition OFF/vehicle OFF, disconnect the X2 harness connector at the K73 Telematics Communication Interface Control Module, ignition ON/vehicle in Service Mode.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V, replace the K73 Telematics Communication Interface Control Module.
    • Go to next step: If between 8.0-10.5 V 
  3. Test for less than 1 V between the low reference circuit terminal A and ground.
    • If greater than 1 V 
    1. Ignition OFF/vehicle OFF, disconnect the X2 harness connector at the K73 Telematics Communication Interface Control Module, ignition ON/vehicle in Service Mode.
    2. Test for less than 1 V between the low reference circuit and ground.
      • If 1 V or greater, repair the short to voltage in the circuit.
      • If less than 1 V, replace the K73 Telematics Communication Interface Control Module.
    • Go to next step: If less than 1 V 
  4. Test for greater than 8 V between the signal circuit terminal B and the low reference circuit terminal A.
    • If less than 8 V 
    1. Ignition OFF/vehicle OFF, disconnect the X2 harness connector at the K73 Telematics Communication Interface Control Module.
    2. Test for infinite resistance between the low reference circuit and ground.
      • If less than infinite resistance, repair the short to ground in the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the vehicle K73 Telematics Communication Interface Control Module.
    • Go to next step: If greater than 8 V 
  5. Test or replace the B24 Cellular Phone Microphone.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.