Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Fastener Specifications
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|---|
| Application |
| Catalytic Converter Gasket |
| Exhaust Front Pipe Gasket |
| Exhaust Gasket |
| Exhaust Manifold Gasket |
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|
|---|---|
| Application | Specification |
| Metric (English) | |
| Exhaust Manifold Fastener | |
| First Pass: | 20 N.m (15 lb ft) |
| Second Pass: | 20 N.m (15 lb ft) |
| Final Pass: | 20 N.m (15 lb ft) |
| Warm Up Three-Way Catalytic Converter Nut (LFY) | 58 N.m (43 lb ft) |
|
NOTE:
All fasteners listed in this table can be reused after removal. |
|
|---|---|
| Application | Specification |
| Metric (English) | |
| Catalytic Converter Brace Bracket Bolt | 22 N.m (16 lb ft) |
| Catalytic Converter Heat Shield Bolt | 10 N.m (89 lb in) |
| Catalytic Converter Nut at Catalytic Converter | 22 N.m (16 lb ft) |
| Catalytic Converter Nut at Exhaust Manifold | 50 N.m (37 lb ft) |
| Exhaust Front Pipe Bracket Bolt | 22 N.m (16 lb ft) |
| Exhaust Front Pipe Nut at Exhaust Muffler | 22 N.m (16 lb ft) |
| Exhaust Front Pipe Nut (LFY) | 58 N.m (43 lb ft) |
| Exhaust Front Pipe Nut at Catalytic Converter | 58 N.m (43 lb ft) |
| Exhaust Front Underbody Heat Shield Retainer | 1.5 N.m (13 lb in) |
| Exhaust Intermediate Hanger Bolt | 22 N.m (16 lb ft) |
| Exhaust Manifold Brace Fastener | 25 N.m (18 lb ft) |
| Exhaust Manifold Heat Shield Fastener | 14 N.m (10 lb ft) |
| Exhaust Muffler Flange Nut | 22 N.m (16 lb ft) |
| Exhaust Pipe Front Hanger Bracket Bolt | 22 N.m (16 lb ft) |
| Exhaust Rear Muffler Heat Shield Retainer | 1.5 N.m (13 lb in) |
| Exhaust Rear Muffler Rear Hanger Bolt | 22 N.m (16 lb ft) |
| Front Cradle Brace Bolt | 58 N.m (43 lb ft) |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.