Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Circuit/System Testing
Each device may need to be disconnected to isolate a circuit fault. Use the schematic to identify the following:
- All low speed GMLAN devices the vehicle is equipped with
- Low speed GMLAN device and splice locations on the low speed GMLAN serial data circuit
- The low speed GMLAN serial data circuit terminals for each device or splice
Testing the Serial Data Circuits for a Short to Voltage
- Ignition/Vehicle OFF, cut the appropriate harness at a low speed GMLAN serial data splice closest to the X84 Data Link Connector, at least 40 mm (1.57 in) from the splice, ignition ON/Vehicle In Service Mode.
- Test for less than 4.5 V between the serial data circuit terminal 1 at the X84 Data Link Connector and ground.
- If 4.5 V or greaterÂ
Repair the short to voltage on the serial data circuit between the X84 Data Link Connector and the splice.
- If less than 4.5 VÂ
- If 4.5 V or greaterÂ
- Test for less than 4.5 V between each low speed GMLAN serial data circuit that was just cut and ground.
- If each serial data circuit is 4.5 V or lessÂ
Inspect/repair the splice.
- If any serial data circuit is greater than 4.5 VÂ
- If each serial data circuit is 4.5 V or lessÂ
- Ignition/Vehicle OFF, reconnect/repair all serial data circuits at the tested splice except the failed serial data circuit, ignition ON/Vehicle In Service Mode.
- Verify the low speed GMLAN devices that are still not communicating to identify the failed serial data circuit.
- Ignition/Vehicle OFF, disconnect all devices on the failed serial data circuit, ignition ON/Vehicle In Service Mode.
- Test for less than 1 V between each section of the failed serial data circuit and ground.
- If 1 V or greaterÂ
Repair the short to voltage in the serial data circuit.
- If less than 1 VÂ
- If 1 V or greaterÂ
- Ignition/Vehicle OFF, reconnect/repair the failed circuit to the splice and connect the first device on the failed serial data circuit, ignition ON/Vehicle In Service Mode.
- Verify the scan tool communicates or not with the low speed GMLAN serial data circuit.
- If the scan tool does not communicateÂ
Replace the device that was just connected.
- If the scan tool communicates and there are more devices to connectÂ
Connect the next device and repeat step 8.
- If the scan tool communicates and there are no more devices to connectÂ
- If the scan tool does not communicateÂ
- All OK.
Do not cut the wires right at the splice. Make sure to cut the wires at least 40 mm (1.57 in) from the splice so the wires can be repaired after the test was done.
Testing the Serial Data Circuits for a Short to Ground
- Ignition/Vehicle OFF, all access doors closed, all vehicle systems OFF, and all keys at least 3 m (9.8 ft) away from vehicle. It may take up to 2 min for all vehicle systems to power down. Cut the appropriate harness at a low speed GMLAN serial data splice closest to the X84 Data Link Connector, at least 40 mm (1.57 in) from the splice.
- Test for infinite resistance between the serial data circuit terminal 1 at the X84 Data Link Connector and ground.
- If less than infinite resistanceÂ
Repair the short to ground on the serial data circuit between the X84 Data Link Connector and the splice.
- If infinite resistanceÂ
- If less than infinite resistanceÂ
- Test for greater than 100 Ω between each low speed GMLAN serial data circuit that was just cut and ground.
- If each serial data circuit is 100 Ω or greaterÂ
Inspect/repair the splice.
- If any serial data circuit is less than 100 ΩÂ
- If each serial data circuit is 100 Ω or greaterÂ
- Reconnect/repair all serial data circuits at the tested splice except the failed serial data circuit, ignition ON/Vehicle In Service Mode.
- Verify the low speed GMLAN devices that are still not communicating to identify the failed serial data circuit.
- Ignition/Vehicle OFF, disconnect all devices on the failed serial data circuit.
- Test for infinite resistance between each section of the failed serial data circuit and ground.
- If less than infinite resistanceÂ
Repair the short to ground in the circuit.
- If infinite resistanceÂ
- If less than infinite resistanceÂ
- Reconnect/repair the failed circuit to the splice and connect the first device on the failed serial data circuit, ignition ON/Vehicle In Service Mode.
- Verify the scan tool communicates or not with the low speed GMLAN serial data circuit.
- If the scan tool does not communicateÂ
Replace the device that was just connected.
- If the scan tool communicates and there are more devices to connectÂ
Connect the next device and repeat step 8.
- If the scan tool communicates and there are no more devices to connectÂ
- If the scan tool does not communicateÂ
- All OK.
Do not cut the wires right at the splice. Make sure to cut the wires at least 40 mm (1.57 in) from the splice so the wires can be repaired after the test was done.
Testing the Serial Data Circuit for an Open/High Resistance
- Ignition/Vehicle OFF, all access doors closed, all vehicle systems OFF, and all keys at least 3 m (9.8 ft) away from vehicle. Disconnect the harness connectors at the non-communicating low speed GMLAN device closest to the X84 Data Link Connector. It may take up to 2 min for all vehicle systems to power down.
- Test for less than 2 Ω between the low speed GMLAN serial data circuit end to end between the device harness connector and the X84 Data Link Connector terminal 1.
- If 2 Ω or greaterÂ
Repair the open/high resistance in the serial data circuit.
- If less than 2 ΩÂ
- If 2 Ω or greaterÂ
- Replace the device that was disconnected.
Testing the Device Circuits
- Ignition/Vehicle OFF, all access doors closed, all vehicle systems OFF, and all keys at least 3 m (9.8 ft) away from vehicle. Disconnect the harness connectors at a low speed GMLAN device that is not communicating. It may take up to 2 min for all vehicle systems to power down.
- Test for less than 10 Ω between each ground circuit terminal and ground.
- If 10 Ω or greaterÂ
- Ignition/Vehicle OFF.
- Test for less than 2 Ω in the ground circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, repair the open/high resistance in the ground connection.
- If less than 10 ΩÂ
- If equipped, verify a test lamp illuminates between each B+ circuit terminal and ground.
- If the test lamp does not illuminate and the circuit fuse is goodÂ
- Ignition/Vehicle OFF, remove the test lamp.
- Test for less than 2 Ω in the B+ circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, verify the fuse is not open and there is voltage at the fuse.
- If the test lamp does not illuminate and the circuit fuse is openÂ
- Ignition/Vehicle OFF, remove the test lamp.
- Test for infinite resistance between the B+ circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- If infinite resistance, replace the disconnected device.
- If the test lamp illuminatesÂ
- Ignition ON/Vehicle In Service Mode.
- If equipped, verify a test lamp illuminates between each ignition circuit terminal, which has a fuse in the circuit, and ground.
- If the test lamp does not illuminate and the circuit fuse is goodÂ
- Ignition/Vehicle OFF, remove the test lamp.
- Test for less than 2 Ω in the ignition circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, verify the fuse is OK and there is voltage at the fuse.
- If the test lamp does not illuminate and the circuit fuse is openÂ
- Ignition/Vehicle OFF, remove the test lamp.
- Test for infinite resistance between the ignition circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- If infinite resistance, replace the disconnected device.
- If the test lamp illuminatesÂ
- If equipped, verify a test lamp illuminates between each ignition circuit terminal, which is controlled by a control module, and ground.
- If the test lamp does not illuminateÂ
- Ignition/Vehicle OFF, remove the test lamp, disconnect the harness connectors at the control module that controls the ignition circuit.
- Test for infinite resistance between the ignition circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- If infinite resistance
- Test for less than 2 Ω in the ignition circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, replace the control module that controls the ignition circuit.
- If the test lamp illuminatesÂ
- Ignition/Vehicle OFF, all access doors closed, all vehicle systems OFF, and all keys at least 3 m (9.8 ft) away from vehicle. It may take up to 2 min for all vehicle systems to power down.
- Test for less than 2 Ω in the low speed GMLAN serial data circuit end to end between the device harness connector and the X84 Data Link Connector terminal 1.
- If 2 Ω or greaterÂ
Repair the open/high resistance in the serial data circuit.
- If less than 2 ΩÂ
- If 2 Ω or greaterÂ
- Replace the device that was disconnected.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
