Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2017 Chevrolet SS Automatic TransFACTORY OEM SERVICE PROCEDURE
Fastener Specifications
Reusable Threaded Fastener Tightening Specifications
|
NOTE:
All fasteners listed in this table can be reused after removal. |
|
|---|---|
| Application | Specification |
| Metric (English) | |
| Battery Hold Down Retainer Fastener | 17 N.m (13 lb ft) |
| Battery Strap Fastener | 22 N.m (16 lb ft) |
| Battery Tray Mounting Bolt | 25 N.m (18 lb ft) |
| Battery Negative Cable at Battery Negative Post Clamp Fastener | 5 N.m (44 lb in) |
| Battery Negative Cable Ground Fastener | 25 N.m (18 lb ft) |
| Battery Positive Cable at Accessory Wiring Junction Block Stud Fastener (LS3) | 9 N.m (80 lb in) |
| Battery Positive Cable at B + Stud Fastener (LS3) | 10 N.m (89 lb in) |
| Battery Positive Cable at Battery Clamp Fastener | 5 N.m (44 lb in) |
| Battery Positive Cable at Battery Positive Post Fastener | 5 N.m (44 lb in) |
| Battery Positive Cable at Body Front Wiring Harness Fuse Block Fastener (LS3) | 9 N.m (80 lb in) |
| Battery Positive Cable at Passthrough Stud Fastener | 15 N.m (11 lb ft) |
| Battery Positive Cable at Starter B + Stud Fastener (LS3) | 10 N.m (89 lb in) |
| Battery Positive Cable Bracket at Engine Block Stud Fastener (LS3) | 9 N.m (80 lb in) |
| Battery Positive Cable Terminal at Body Front Wiring Harness Fuse Block Barrel Fastener (LS3) | 9 N.m (80 lb in) |
| Battery Positive Cable Terminal at Generator B + Stud Fastener (LS3) | 10 N.m (89 lb in) |
| Battery Positive Cable Terminal at Starter Solenoid Fastener (LS3) | 10 N.m (89 lb in) |
| Battery Positive Extension Cable at Plenum Passthrough Stud Fastener | 15 N.m (11 lb ft) |
| Battery Positive Junction Block Stud | 15 N.m (11 lb ft) |
| Body Harness Ground Fastener | 9 N.m (80 lb in) |
| Engine Ground Cable at Engine Block (LS3) | 25 N.m (18 lb ft) |
| Engine Ground Cable at Wheelhouse Panel Fastener (LS3) | 22 N.m (16 lb ft) |
| Engine Wiring and Battery Positive Cable Conduit Fastener (LS3) | 9 N.m (80 lb in) |
| Engine Wiring Harness at Body Front Wiring Harness Fuse Block Fastener (LS3) | 9 N.m (80 lb in) |
| Generator Bracket Fastener (LS3) | 58 N.m (43 lb ft) |
| Heat Shield at Starter Motor Retaining Bolt (LS3) | 5 N.m (44 lb in) |
| Heat Shield Retaining Fastener (LS3) | 5 N.m (44 lb in) |
| Mega Fuse Case at Body Front Wiring Harness Fuse Block Barrel Fastener (LS3) | 9 N.m (80 lb in) |
| Rear Generator Brace at Generator Fastener (LS3) | 58 N.m (43 lb ft) |
| Starter Mounting Fastener (LS3) | 58 N.m (43 lb ft) |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.