2015 Chevrolet VoltFACTORY OEM SERVICE PROCEDURE

Flashing Yellow Indicator

  1. Vehicle OFF, disconnect the X3 harness connector from T18 Battery Charger.
  2. Test for infinite resistance between the terminals listed below at the X98 Hybrid/EV Battery Charger Receptacle:
    Fig 1: X98 Hybrid/EV Battery Charger Receptacle And Terminals
    GM2874492Courtesy of GENERAL MOTORS COMPANY
    • 110/220 V A/C Line 1 terminal E and 110/220 V A/C Neutral Line 2 terminal A
    • 110/220 V A/C Line 1 terminal E and 110/220 V A/C Ground terminal C
    • 110/220 V A/C Line 1 terminal E and Control pilot signal circuit terminal B
    • 110/220 V A/C Line 1 terminal E and Proximity status signal circuit terminal D
    • 110/220 V A/C Neutral Line 2 terminal A and 110/220 V A/C Ground terminal C
    • 110/220 V A/C Neutral Line 2 terminal A and Control pilot signal circuit terminal B
    • 110/220 V A/C Neutral Line 2 terminal A and Proximity status signal circuit terminal D
    • 110/220 V A/C Ground terminal C and Control pilot signal circuit terminal B
    • Control pilot signal circuit terminal B and Proximity status signal circuit terminal D
    • If less than infinite resistance 
    1. Disconnect the harness connector from the X98 Hybrid/EV Battery Charger Receptacle.
    2. Test for infinite resistance between the terminals listed below at the X98 Hybrid/EV Battery Charger Receptacle:
      Fig 2: X98 Hybrid/EV Battery Charger Receptacle And Terminals
      GM2874492Courtesy of GENERAL MOTORS COMPANY
    3. 110/220 V A/C Line 1 terminal E and 110/220 V A/C Neutral Line 2 terminal A
    4. 110/220 V A/C Line 1 terminal E and 110/220 V A/C Ground terminal C
    5. 110/220 V A/C Line 1 terminal E and Control pilot signal circuit terminal B
    6. 110/220 V A/C Line 1 terminal E and Proximity status signal circuit terminal D
    7. 110/220 V A/C Neutral Line 2 terminal A and 110/220 V A/C Ground terminal C
    8. 110/220 V A/C Neutral Line 2 terminal A and Control pilot signal circuit terminal B
    9. 110/220 V A/C Neutral Line 2 terminal A and Proximity status signal circuit terminal D
    10. 110/220 V A/C Ground terminal C and Control pilot signal circuit terminal B
    11. Control pilot signal circuit terminal B and Proximity status signal circuit terminal D
      • If less than infinite resistance, replace the X98 Hybrid/EV Battery Charger Receptacle and K114B Hybrid/EV Powertrain Control Module 2.
      • If infinite resistance
    12. Disconnect the X2 harness connector from K114B Hybrid/EV Powertrain Control Module 2
    13. Test for infinite resistance between the circuits.
      • If less than infinite resistance, repair the short between the circuits.
      • If infinite resistance, replace the K114B Hybrid/EV Powertrain Control Module 2.
    • If infinite resistance 
  3. Replace the K114B Hybrid/EV Powertrain Control Module 2.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.