SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2015CAPTIVA SPORT LTZREPAIR AND DIAGNOSISENGINE PERFORMANCESYSTEMDATA COMMUNICATION SYSTEMDIAGNOSTIC INFORMATION AND PROCEDURESDTC U18A2: LOST COMMUNICATION WITH FUEL PUMP DRIVER CONTROL MODULECIRCUIT/SYSTEM TESTING
2015 Chevrolet Captiva Sport LTZ

Circuit/System Testing

2015 Chevrolet Captiva Sport LTZSECTION Circuit/System Testing
NOTE:

Use the schematics and connector end views to identify the device's ground, B+, ignition, accessory wake up serial data, and serial data circuit terminals.

  1. Ignition OFF, all access doors closed, all vehicle systems OFF, and all keys at least 3 m (9.8 ft) away from vehicle. Disconnect the harness connectors at the K111 Fuel Pump Driver Control Module. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between each ground circuit terminal and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON.
  4. If equipped, verify a test lamp illuminates between each B+ circuit terminal and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF, remove the test lamp.
    2. Test for less than 2 Ω in the B+ circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is not open and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF, remove the test lamp.
    2. Test for infinite resistance between the B+ circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K111 Fuel Pump Driver Control Module.
    • If the test lamp illuminates 
  5. If equipped, verify a test lamp illuminates between each ignition circuit terminal and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF, remove the test lamp.
    2. Test for less than 2 Ω in the ignition circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is OK and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF, remove the test lamp.
    2. Test for infinite resistance between the ignition circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K111 Fuel Pump Driver Control Module.
    • If the test lamp illuminates 
  6. If equipped, verify a test lamp illuminates between the accessory wakeup serial data circuit terminal and ground.
    • If the test lamp does not illuminate 
    1. Ignition OFF, remove the test lamp, disconnect the harness connectors at the K9 Body Control Module.
    2. Test for infinite resistance between the accessory wakeup serial data circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the accessory wakeup serial data circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp illuminates 
  7. Test for less than 4.5 V between each powertrain high speed GMLAN serial data circuit terminal and ground.
    • If 4.5 V or greater 

      Refer to DTC U0074  to test for a short to voltage.

    • If less than 4.5 V 
  8. Ignition OFF, all access doors closed, all vehicle systems OFF, and all keys at least 3 m (9.8 ft) away from vehicle. It may take up to 2 min for all vehicle systems to power down.
  9. Test for greater than 100 Ω between each powertrain high speed GMLAN serial data circuit terminal and ground.
    • If 100 Ω or less 

      Refer to DTC U0074  to test for a short to ground.

    • If greater than 100 Ω 
  10. Disconnect the harness connectors at the device setting the DTC.
  11. Test for less than 2 Ω in each serial data circuits end to end between the K111 Fuel Pump Driver Control Module and the device setting the DTC.
    • If 2 Ω or greater 

      Repair the open/high resistance in the serial data circuit.

    • If less than 2 Ω 
  12. Replace the K111 Fuel Pump Driver Control Module.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.