Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2011 Chevrolet Volt L4-1.4L ElectFACTORY OEM SERVICE PROCEDURE
Connecting Rod, Engine
Connecting Rod Bearing Cap 25 Nm + 45° (18 lb ft + 45°)
Conrod Bearing Journal Diameter Standard
42.971mm - 42.987mm
1.6918in - 1.6924in
Conrod Bearing Journal Diameter Undersize 0.25 (blue)
42.721mm - 42.737mm
1.6819in - 1.6826in
Conrod Bearing Journal Diameter Undersize 0.5 (white)
42.471mm - 42.487mm
1.6721in - 1.6727in
Conrod Bearing Thickness Standard
1.490mm - 1.500mm
0.0587in - 0.0591in
Conrod Bearing Thickness Undersize 0.25
1.615mm - 1.625mm
0.0636in - 0.064in
Conrod Bearing Thickness Undersize 0.5
1.740mm - 1.750mm
0.0685in - 0.0689in
Conrod Bearing Diameter Standard (upper and lower)
1.490mm - 1.500mm
0.0587in - 0.0591in
Conrod Bearing Diameter Undersize 0.25 (upper and lower)
1.615mm - 1.625mm
0.0636in - 0.064in
Conrod Bearing Diameter Undersize 0.5 (upper and lower)
1.740mm - 1.750mm
0.0685in - 0.0689in
Conrod Bearing Clearance
0.013mm - 0.061mm
0.0005in - 0.0024in
Conrod Bearing Journal Diameter Standard
42.971mm - 42.987mm
1.6918in - 1.6924in
Conrod Bearing Journal Diameter Undersize 0.25 (blue)
42.721mm - 42.737mm
1.6819in - 1.6826in
Conrod Bearing Journal Diameter Undersize 0.5 (white)
42.471mm - 42.487mm
1.6721in - 1.6727in
Conrod Bearing Thickness Standard
1.490mm - 1.500mm
0.0587in - 0.0591in
Conrod Bearing Thickness Undersize 0.25
1.615mm - 1.625mm
0.0636in - 0.064in
Conrod Bearing Thickness Undersize 0.5
1.740mm - 1.750mm
0.0685in - 0.0689in
Conrod Bearing Diameter Standard (upper and lower)
1.490mm - 1.500mm
0.0587in - 0.0591in
Conrod Bearing Diameter Undersize 0.25 (upper and lower)
1.615mm - 1.625mm
0.0636in - 0.064in
Conrod Bearing Diameter Undersize 0.5 (upper and lower)
1.740mm - 1.750mm
0.0685in - 0.0689in
Conrod Bearing Clearance
0.013mm - 0.061mm
0.0005in - 0.0024in
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
