Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Chevrolet Uplander V6-3.9LFACTORY OEM SERVICE PROCEDURE
Computers and Control Systems: Technical Service Bulletins
- Recalls
- Customer Interest
- Electrical - MIL ON/DTC's Set By Various Control Modules
- Electrical - Intermittent MIL/DTC P2138/Reduced Power
- A/T - Harsh Shifts/Slipping/DTCs P0741/P0742/P0757/P842
- Cooling System - MIL ON/Overheating/Coolant Loss
- Engine, A/T - Shift/Driveability Concerns/MIL ON
- A/T Controls - MIL ON/Harsh Shifts/DTC's P0742/P2761
- Electrical - Hard or No Start/Warning Lamps ON/DTC's Set
- By Symptom
- Abnormal wear/deterioration
- Customer Interest
- Electrical - MIL ON/DTC's Set By Various Control Modules
- Electrical - Intermittent MIL/DTC P2138/Reduced Power
- A/T - Harsh Shifts/Slipping/DTCs P0741/P0742/P0757/P842
- Cooling System - MIL ON/Overheating/Coolant Loss
- Engine, A/T - Shift/Driveability Concerns/MIL ON
- A/T Controls - MIL ON/Harsh Shifts/DTC's P0742/P2761
- Electrical - Hard or No Start/Warning Lamps ON/DTC's Set
- Driveability
- Erratic Operation
- Erratic Shifting
- False instrument warning light/gauges
- Hard Shifting
- Leaks
- Overheating
- Recalls
- Slipping
- Starting problems
- All Technical Service Bulletins
- Electrical - Aftermarket Interface Devices Causing Issues
- Engine - THIS BULLETIN HAS BEEN CANCELED
- A/T Controls - Snapshot Data With Tech2(R) Information
- Electrical - MIL ON/DTC's Set By Various Control Modules
- Electrical - Intermittent MIL/DTC P2138/Reduced Power
- A/T Control - DTC P0756 Diagnostic Tips
- Electrical - Reducing Intermittent Electrical Concerns
- A/T - Diagnostic Information for DTC's P0894/P1870
- A/T - Harsh Shifts/Slipping/DTCs P0741/P0742/P0757/P842
- Campaign - ECM Updates for Virtual Flex Fuel Sensor
- Recall - ECM Upate for Ethanol Enabling
- Cooling System - MIL ON/Overheating/Coolant Loss
- Computers - Radio Fuse Removal Prior to Programming
- Engine, A/T - Shift/Driveability Concerns/MIL ON
- A/T Controls - MIL ON/Harsh Shifts/DTC's P0742/P2761
- Emissions - OBDII I/M Readiness Testing
- Electrical - Hard or No Start/Warning Lamps ON/DTC's Set
- Engine Controls - MIL Function During I/M Testing
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
