Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Chevrolet Express 2500 V8-4.8LFACTORY OEM SERVICE PROCEDURE
Computers and Control Systems: Technical Service Bulletins
- Customer Interest
- Fuel System - Driveability Concerns/MIL ON/Multiple DTC's
- Engine - MIL ON P0116/P1400 Set In Very Cold Temps
- Electrical - MIL ON/DTC's Set By Various Control Modules
- Electrical - Intermittent MIL/DTC P2138/Reduced Power
- A/T- Slips/Overheats/Won't Shift/MIL ON/DTCs P0218/P0894
- A/T - Slips/Harsh Shifts/Delayed Shifts/Multiple DTC's
- Engine, A/T - Shift/Driveability Concerns/MIL ON
- Engine Controls - MIL ON/Misfire/Misfire DTC's Set
- By Symptom
- Abnormal wear/deterioration
- Customer Interest
- Fuel System - Driveability Concerns/MIL ON/Multiple DTC's
- Engine - MIL ON P0116/P1400 Set In Very Cold Temps
- Electrical - MIL ON/DTC's Set By Various Control Modules
- Electrical - Intermittent MIL/DTC P2138/Reduced Power
- A/T- Slips/Overheats/Won't Shift/MIL ON/DTCs P0218/P0894
- A/T - Slips/Harsh Shifts/Delayed Shifts/Multiple DTC's
- Engine, A/T - Shift/Driveability Concerns/MIL ON
- Engine Controls - MIL ON/Misfire/Misfire DTC's Set
- Driveability
- Erratic Shifting
- Hard Shifting
- Loose
- No shift/Incorrect gear engagement
- Overheating
- Slipping
- Starting problems
- All Technical Service Bulletins
- Electrical - Aftermarket Interface Devices Causing Issues
- Engine Controls - Non-GM Engine/Transmission Calibration ID
- Fuel System - Driveability Concerns/MIL ON/Multiple DTC's
- Engine - THIS BULLETIN HAS BEEN CANCELED
- A/T Controls - Snapshot Data With Tech2(R) Information
- Engine - MIL ON P0116/P1400 Set In Very Cold Temps
- Electrical - MIL ON/DTC's Set By Various Control Modules
- Electrical - Intermittent MIL/DTC P2138/Reduced Power
- Fuel System -07-06-04-022G End Of Need For Information
- A/T Control - DTC P0756 Diagnostic Tips
- Electrical - Reducing Intermittent Electrical Concerns
- Emissions - Diagnostic Tips For DTC's P0443/P0455
- A/T - Diagnostic Information for DTC's P0894/P1870
- A/T- Slips/Overheats/Won't Shift/MIL ON/DTCs P0218/P0894
- A/T - MIL ON/DTC P0757/Harsh or Slipping 2-3 Shift
- A/T - Slips/Harsh Shifts/Delayed Shifts/Multiple DTC's
- Engine, A/T - Shift/Driveability Concerns/MIL ON
- Emissions - OBDII I/M Readiness Testing
- Engine Controls - MIL ON/Misfire/Misfire DTC's Set
- Engine Controls - MIL Function During I/M Testing
- Engine/Transmission - Aftermarket Calibrations
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
