2006 Chevrolet HHR LS, AutomaticFACTORY OEM SERVICE PROCEDURE

Scan Tool Data List

The Engine Scan Tool Data List contains all engine related parameters that are available on the scan tool. The list is arranged in alphabetical order. The parameters in the Typical Scan Data values column represent values that would be seen on a normally running engine.

IMPORTANT: A scan tool that displays faulty data should not be used, and the problem should be reported to the scan tool manufacturer. Use of a faulty scan tool can result in misdiagnosis and unnecessary parts replacement.

Only the parameters listed below are referred to in this service manual for use in diagnosis. For further information on using the scan tool to diagnose the powertrain control module (PCM) and related sensors, refer to the applicable reference section listed below. If all values are within the typical range described below, refer to Symptoms - Engine Controls for diagnosis. The Typical Scan Data Values table contains all the parameters included in the following data lists arranged in alphabetical order:

  • Engine Data 1-Contains general information regarding fuel delivery and basic engine operating conditions.
  • Engine Data 2-Contains general information regarding A/C, crankshaft position (CKP), camshaft position (CMP), knock sensor (KS), and basic engine operating conditions.
  • Engine Data 3-Contains general information regarding fuel delivery, engine coolant temperature (ECT), intake air temperature (IAT), vehicle theft deterrent (VTD), and basic engine operating conditions.
  • Evaporative Emission (EVAP) Data-Contains information specific to the EVAP control system. Also displays parameters required to verify proper EVAP system operation.
  • Fuel Trim Data-Contains specific information regarding fuel trim.
  • Misfire Data-Contains specific information regarding misfire diagnostics and parameters required to verify proper operation with regard to misfire.

For scan tool parameter definitions, refer to Scan Tool Data Definitions .

IMPORTANT: Use the Typical Scan Data Values only after the following conditions are met:
  • The Diagnostic System Check - Vehicle in Vehicle DTC Information has been completed.
  • The engine is idling unless checking a value at a specified RPM.
  • The throttle is closed unless checking a value at a specified RPM.
  • The vehicle is in PARK or NEUTRAL.
  • The vehicle is operating in Closed Loop.
  • The vehicle accessories are turned OFF.
Typical Scan Tool Data List

Scan Tool Parameter Data List Units Displayed Typical Data Value
A/C High Side Pressure Engine 2 Volts 0-5.0 Volts
A/C High Side Pressure Engine 2 kPa/psi 0-3100 kPa (0-450 psi) (Varies with the refrigerant pressure)
A/C Relay Command Engine 1
Engine 2
Engine 3
Misfire
ON/OFF OFF (ON with the A/C requested)
A/C Request Signal Engine 2 Yes/No No (Yes with A/C ON)
Air Flow Calculated Engine 1
Engine 2
Engine 3
Fuel Trim
Misfire
g/s Varies
Air/Fuel Ratio Engine 2
Engine 3
Fuel Trim
Ratio 14.6:1 (Varies)
BARO Engine 1
EVAP
Fuel Trim
kPa 65-104 (Varies with the altitude and barometric pressure)
CKP Active Counter (7X Reference) Engine 2 0-255 Counts 0-255-Increments while cranking or running
CMP Active Counter Engine 2 0-255 Counts 0-255-Increments while cranking or running
CMP Resync Counter Engine 2 0-255 Counts 0
Cruise Control Active Engine 1
Engine 2
Engine 3
Yes/No No
Cruise Release Clutch/ TCC Pedal Switch Engine 1
Engine 2
Engine 3
Applied/Released Released
Current Gear Engine 1
Engine 2
Fuel Trim
1-6 6
Cycles of Misfire Data Misfire Counts 0-99 (Varies)
Desired Idle Speed Engine 1
Engine 2
Engine 3
EVAP
RPM PCM commanded idle speed (Varies with calibration)
ECT Sensor Engine 1
Engine 2
Engine 3
EVAP
Fuel Trim
Misfire
°C-°F 85-115°C (185-239°F) (Varies with coolant temperature)
Engine Load Engine 1
Engine 2
Engine 3
EVAP
Fuel Trim
Misfire
% 11-21%
16-29% at 2,500 RPM
Engine Oil Life Remaining Engine 3 % 0-100% (Varies)
Engine Oil Pressure Switch Engine 3 Low/OK OK (Low with low oil pressure)
Engine Run Time Engine 1
Engine 2
Engine 3
EVAP
Fuel Trim
Misfire
Hr:Min:Sec Depends on time since startup
Engine Speed Engine 1
Engine 2
Engine 3
EVAP
Fuel Trim
Misfire
RPM +/-100 RPM from Desired Idle
EVAP Purge Solenoid Command Engine 1
EVAP
Fuel Trim
% 0-100% (Varies)
EVAP Vent Solenoid Command Engine 1
EVAP
Fuel Trim
Venting/Non-venting Varies
FC Relay 1 Engine 2
Engine 3
ON/OFF OFF (Varies with fan request)
FC Relay 2 Engine 2
Engine 3
ON/OFF OFF (Varies with fan request)
Fuel Level Sensor Engine 1
EVAP
% 0-100% Depends on fuel level
Fuel Pump Relay Command Engine 1 ON/OFF ON
Fuel Tank Pressure Sensor Engine 1
EVAP
mmHg/in H2O Depends on Pressure/Vacuum
Fuel Tank Pressure Sensor EVAP Volts Depends on Pressure/Vacuum
Fuel Trim Cell Engine 1
EVAP
Fuel Trim
Cell number 18-21 at idle (Varies with the air flow, RPM P/N and A/C)
Fuel Trim Index Fuel Trim % 0% +/- 10%
Generator F Terminal Signal Engine 2 % 0-100% (Varies)
Generator L Terminal Signal Engine 2 ON/OFF Varies
HO2S 1 Engine 1
EVAP
Fuel Trim
mV 1-1,000, constantly Varying
HO2S 2 Engine 1
Fuel Trim
mV 0-1,000, constantly Varying
HO2S 1 Heater Current Fuel Trim amps 0.58-0.64 amps
HO2S 2 Heater Current Fuel Trim amps 0.58-0.64 amps
IAC Position Engine 1
Fuel Trim
Counts 5-60
IAT Sensor Engine 1
Engine 2
Engine 3
EVAP
Fuel Trim
°C-°F 10-80°C (50-176°F Varies with underhood temperature)
Ignition 1 Signal Engine 1
Engine 2
Engine 3
EVAP
Fuel Trim
Volts 12.0-15.0 Volts (Varies)
Injector PWM Engine 2
Fuel Trim
Misfire
mS 3-4 mS
Injector 1 Command Engine 3 mS 3-4 mS
Injector 2 Command Engine 3 mS 3-4 mS
Injector 3 Command Engine 3 mS 3-4 mS
Injector 4 Command Engine 3 mS 3-4 mS
Knock Retard Engine 1 Degrees 0°
Long Term FT Engine 1
Engine 2
Engine 3
EVAP
Fuel Trim
0% +/- 10% 58-198 (-100% to +100% Varies)
Loop Status Engine 1
Engine 2
Engine 3
EVAP
Fuel Trim
Open/Closed Closed
MAP Sensor Engine 1
Engine 2
Engine 3
EVAP
Fuel Trim
Misfire
kPa 25-48 kPa
MAP Sensor Engine 1
Engine 2
Engine 3
Volts 1-3 Volts (Varies with the vacuum and BARO pressure)
Med. Resolution Resync Counter Engine 2 0-255 Counts 0
MIL Command Engine 1 ON/OFF OFF (with no codes)
Misfire Current #1-#4 Misfire 0-255 Counts 0 (increase with a misfire)
Misfire History #1-#4 Misfire 0-255 Counts 0 (increase with a misfire)
Number of DTCs Engine 1
EVAP
Fuel Trim
Number 0
Power Enrichment Engine 2
Fuel Trim
Misfire
Active/Inactive Inactive
Short Term FT Engine 1
Engine 2
Engine 3
EVAP
Fuel Trim
% 0% +/- 10%
Spark Engine 1
Engine 2
Engine 3
Fuel Trim
Misfire
Degrees Varies
Start Up ECT Engine 2
EVAP
Fuel Trim
°C-°F Varies with start up temperature
TCC Enable Solenoid Command Engine 1
Engine 2
Misfire
ON/OFF ON
TP Sensor Engine 1
Engine 2
EVAP
Fuel Trim
Misfire
% 0% (up to 100% at wide open throttle)
TP Sensor Engine 1
Engine 2
Engine 3
Volts 0.200-0.900 volts (up to 5.0 volts at wide open throttle)
TR Switch Engine 2
Engine 3
Fuel Trim
Low/High Low/Low/High/High
TWC Temperature Calculated Fuel Trim °C-°F Varies
Vehicle Speed Sensor Engine 1
Engine 2
Engine 3
EVAP
Fuel Trim
Misfire
Km/h/mph 0
VTD Auto. Learn Timer Engine 3 Active/Inactive Inactive
VTD Fuel Disable Engine 3 Active/Inactive Inactive
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.