Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Chevrolet Epica LSFACTORY OEM SERVICE PROCEDURE
Fastener Tightening Specifications
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Camshaft Position (CMP) Sensor Retaining Bolt | 12 N.m | 106 lb in |
| Crankshaft Position (CKP) Sensor Heat Shield Housing Bolt | 8 N.m | 71 lb in |
| Crankshaft Position (CKP) Sensor Retaining Bolt | 7 N.m | 62 lb in |
| Engine Control Module (ECM) Bracket Nut | 12 N.m | 106 lb in |
| Engine Control Module (ECM) Retaining Nut | 12 N.m | 106 lb in |
| Engine Coolant Temperature (ECT) Sensor | 17 N.m | 13 lb ft |
| Exhaust Gas Recirculation (EGR) Adapter Retaining Bolt | 20 N.m | 15 lb ft |
| Exhaust Gas Recirculation (EGR) Pipe Retaining Bolt/Nut | 10 N.m | 89 lb in |
| Exhaust Gas Recirculation (EGR) Pipe-to-Bracket Cylinder Head Long Side Retaining Bolt | 10 N.m | 89 lb in |
| Exhaust Gas Recirculation (EGR) Pipe-to-Bracket Cylinder Head Short Side Retaining Bolt | 20 N.m | 15 lb ft |
| Exhaust Gas Recirculation (EGR) Valve Retaining Bolt | 25 N.m | 18 lb ft |
| Fuel Filter Protector Retaining Bolt | 4 N.m | 35 lb in |
| Fuel Pressure Regulator Retaining Bolt | 12 N.m | 106 lb in |
| Ignition Coil Retaining Bolt | 7 N.m | 62 lb in |
| Intake Air Temperature (IAT) Sensor | 25 N.m | 18 lb ft |
| Intake Exhaust Gas Recirculation (EGR) Pipe Retaining Bolt | 10 N.m | 89 lb in |
| Knock Sensor Retaining Bolt | 19 N.m | 14 lb ft |
| Manifold Absolute Pressure (MAP) Sensor | 8 N.m | 71 lb in |
| Oxygen Sensor (O2S) | 39 N.m | 29 lb ft |
| Spark Plug | 25 N.m | 18 lb ft |
| Throttle Body Assembly Retaining Bolt | 13 N.m | 115 lb in |
| Variable Intake System (VIS) Actuator Retaining Bolt | 12 N.m | 106 lb in |
| Variable Intake System (VIS) Vacuum Tank Retaining Bolt | 8 N.m | 71 lb in |
| Variable Intake System (VIS) Valve Retaining Bolt | 12 N.m | 106 lb in |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
