Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2004 Chevrolet Venture Base, Van Cargo ExtendedFACTORY OEM SERVICE PROCEDURE
Engine Controls Connector End Views
Air Injection BL Value Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 339 | Ignition 1 Voltage |
| B | PNK/BLK | 429 | Air Solenoid Control |
AIR Pump Relay Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 30 | ORN | 3040 | Fused Output |
| 85 | BLK | 339 | Fused Output Ignition 1 |
| 86 | BRN | 436 | AIR Injection Reaction Pump Motor Relay Output - Coil |
| 87 | RED | 78 | AIR Injection Reaction Pump Motor Feed |
Automatic Transaxle (C111) Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | LT GRN | 1222 | 1-2 Shift Solenoid Valve Control |
| B | YEL/BLK | 1223 | 2-3 Shift Solenoid Valve Control |
| C | RED/BLK | 1228 | PC Sol. Valve High Control |
| D | LT BLU/WHT | 1229 | PC Sol. Valve Low Control |
| E | PNK | 1339 | Ignition 1 Voltage |
| F | BLK/WHT | 771 | Transmission Range Switch Signal A |
| G | YEL | 772 | Transmission Range Switch Signal B |
| H | GRY | 773 | Transmission Range Switch Signal C |
| J | WHT | 776 | Transmission Range Switch Signal P |
| K | BLK/WHT | 451 | Ground |
| L | YEL/BLK | 1227 | TFT Sensor Signal |
| M | BLK | 2762 | Low Reference |
| N | PNK | 1224 | Trans Fluid Pressure Switch Signal A |
| P | RED | 1226 | Trans Fluid Pressure Switch Signal C |
| R | DK BLU | 1225 | Trans Fluid Pressure Switch Signal B |
| S | RED/BLK | 1230 | A/T ISS High Signal |
| T | BRN | 418 | TCC PWM Solenoid Valve Control |
| U | YEL | 657 | TCC Release Switch Signal |
| V | DK BLU/WHT | 1231 | A/T ISS Low Signal |
| W | - | - | Not Used |
Camshaft Position (CMP) Sensor Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BLK | 630 | Camshaft Position Signal |
| B | BLK | 407 | Low Reference |
| C | RED/WHT | 812 | 12 Volt Reference |
Crankshaft Position (CKP) Sensor A Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | LT GRN | 1867 | 12 Volt Reference |
| B | LT BLU/BLK | 647 | Medium Resolution Engine Speed Signal |
| C | YEL/BLK | 1868 | Low Reference |
Crankshaft Position (CKP) Sensor B Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | YEL | 573 | CKP Sensor Signal |
| B | PPL | 574 | Low Reference |
Engine Coolant Temperature (ECT) Sensor Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | ORN/BLK | 469 | Low Reference |
| B | YEL | 410 | ECT Sensor Signal |
Engine Oil Level Switch Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BRN | 1174 | Oil Level Switch Signal |
| B | BLK/WHT | 451 | Ground |
Engine Oil Pressure (EOP) Switch Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | TAN/BLK | 231 | Oil Pressure Switch Signal |
Evaporative Emission (EVAP) Canister Purge Solenoid Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 339 | Ignition 1 Voltage |
| B | DK GRN/WHT | 428 | EVAP Canister Purge Solenoid Control |
Evaporative Emission (EVAP) Canister Vent Solenoid Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 1039 | Ignition 1 Voltage |
| B | WHT | 1310 | EVAP Canister Vent Solenoid Control |
Exhaust Gas Recirculation (EGR) Valve Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | GRY | 435 | EGR Solenoid Low Control |
| B | BLK | 2753 | Low Reference |
| C | BRN | 1456 | EGR Valve Position Signal |
| D | GRY | 2702 | 5-Volt Reference |
| E | RED | 1676 | EGR Valve Supply Voltage |
Fuel Injector 1 Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 639 | Ignition 1 Voltage |
| B | BLK | 1744 | Fuel Injector 1 Control |
Fuel Injector 2 Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 639 | Ignition 1 Voltage |
| B | LT GRN/BLK | 1745 | Fuel Injector 2 Control |
Fuel Injector 3 Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 639 | Ignition 1 Voltage |
| B | PNK/BLK | 1746 | Fuel Injector 3 Control |
Fuel Injector 4 Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 639 | Ignition 1 Voltage |
| B | LT BLU/BLK | 844 | Fuel Injector 4 Control |
Fuel Injector 5 Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 639 | Ignition 1 Voltage |
| B | BLK/WHT | 845 | Fuel Injector 5 Control |
Fuel Injector 6 Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PNK | 639 | Ignition 1 Voltage |
| B | YEL/BLK | 846 | Fuel Injector 6 Control |
Fuel Pump Sender Unit C1 Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PPL | 1589 | Fuel Level Sensor Signal |
| B | GRY | 120 | Fuel Pump Supply Voltage |
| C | BLK | 250 | Ground |
| D | BLK | 2759 | Low Reference |
Fuel Tank Pressure Sensor C2 Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BLK/WHT | 2759 | Low Reference |
| B | DK GRN | 890 | Fuel Tank Pressure Sensor Signal |
| C | GRY | 2700 | Volt Reference |
Heated Oxygen Sensor (HO2S 1) Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | TAN | 413 | Low Reference |
| B | PPL | 412 | HO2S 1 Signal |
| C | BLK/WHT | 3113 | HO2S Heater Low Control |
| D | PNK | 339 | Ignition 1 Voltage |
Heated Oxygen Sensor (HO2S 2) Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | TAN/WHT | 1669 | HO2S Low Signal |
| B | PPL/WHT | 1668 | HO2S High Signal |
| C | BLK | 1050 | Ground |
| D | PNK | 339 | Ignition 1 Voltage |
Idle Air Control (IAC) Valve Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | LT GRN/BLK | 444 | IAC Coil B Low Control |
| B | LT GRN/WHT | 1749 | IAC Coil B High Control |
| C | LT BLU/BLK | 1748 | IAC Coil A Low Control |
| D | LT BLU/WHT | 1747 | IAC Coil A High Control |
Ignition Control Module (ICM) C1 Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | TAN/BLK | 424 | IC Timing Signal |
| B | WHT | 423 | IC Timing Control |
| C-D | - | - | Not Used |
| E | PPL/WHT | 430 | Low Resolution Engine Speed Signal |
| F | RED/BLK | 453 | Low Reference |
Ignition Control Module (ICM) C2 Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BLK/WHT | 51 | Ground |
| B | PNK | 239 | Ignition 1 Voltage |
Ignition Control Module (ICM) C3 Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | YEL | 573 | CKP Sensor Signal |
| B | - | - | Not Used |
| C | PPL | 574 | Low Reference |
Intake Air Temperature (IAT) Sensor Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BLK | 2760 | Low Reference |
| B | TAN | 472 | IAT Sensor Signal |
Knock Sensor Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | DK BLU | 496 | Knock Sensor Signal |
Manifold Absolute Pressure (MAP) Sensor Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | ORN/BLK | 469 | Low Reference |
| B | LT GRN | 432 | MAP Sensor Signal |
| C | GRY | 2704 | 5 Volt Reference |
Mass Air Flow (MAF) Sensor Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | YEL | 492 | MAF Sensor Signal |
| B | BLK/WHT | 451 | Ground |
| C | PNK | 339 | Ignition 1 Voltage |
Secondary Air Injection (AIR) Pump Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | RED | 78 | Air Pump Supply Voltage |
| B | BLK | 450 | Ground |
Throttle Position (TP) Sensor Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | GRY | 2701 | 5-Volt Reference |
| B | BLK | 2752 | Low Reference |
| C | DK BLU | 417 | TP Sensor Signal |
Park/Neutral Position (PNP) Switch Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | ORN/BLK | 434 | Neutral Safety Switch Signal |
| B | ORN | 840 | Battery Positive Voltage |
| C | LT GRN | 275 | Park Neutral Position Switch Park Signal |
| D | BLK/WHT | 451 | Ground |
| E | ORN/BLK | 1786 | Park/Neutral Signal |
| F | LT GRN | 24 | Backup Lamp Supply Voltage |
| G | PNK | 439 | Ignition 1 Voltage |
Vehicle Speed Sensor (VSS) Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PPL | 401 | Signal Low - Front |
| B | YEL | 400 | Signal High - Front |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.
