Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2000 Chevrolet Venture PlusFACTORY OEM SERVICE PROCEDURE
Specifications Index
MONTANA, SILHOUETTE & VENTURE SPECIFICATIONS INDEX
| System | Specification/Pressure | |
|---|---|---|
| Air Conditioning | ||
| Service | SPECIFICATIONS | |
| Torque | TORQUE SPECIFICATIONS | |
| Axle Nut/Hub Nut | ||
| Front | 118 Ft. Lbs. (160 N.m) | |
| Battery | NA | |
| Brakes | ||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | |
| Disc Brakes | DISC BRAKE SPECIFICATIONS | |
| Drum Brakes | DRUM BRAKE SPECIFICATIONS | |
| Torque | TORQUE SPECIFICATIONS | |
| Charging | ||
| Generator | ON-VEHICLE TESTING | |
| Torque | TORQUE SPECIFICATIONS | |
| Drive Belts | ||
| Adjustment | BELT ADJUSTMENT | |
| Belt Routing | See appropriate illustration under SERPENTINE BELT ROUTING & ALIGNMENT | |
| Engine Cooling | ||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | |
| Radiator Cap Pressure | 15 psi or specification stamped on Cap | |
| Thermostat R & I | THERMOSTAT | |
| Water Pump R & I | WATER PUMP | |
| Engine Mechanical | ||
| Compression | Lowest compression reading should not be less than 70 percent of highest compression reading. No cylinder compression reading should be less than 100 psi (7 kg/cm2 ). | |
| Oil Pressure | Normal oil pressure is 50-65 psi (3.5-4.5 kg/cm2 ) at 1200 RPM (at normal operating temperature). | |
| Overhaul | ENGINE SPECIFICATIONS | |
| Torque | TORQUE SPECIFICATIONS | |
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |
| Flywheel/Flex Plate Torque | 52 Ft. Lbs. (71 N.m) Apply Thread Locker (12345382) to flexplate/flywheel bolts. | |
| Fuel System | ||
| Pressure Specification | 52-59 psi (3.7-4.1 kg/cm2 ) | |
| Fuel Pressure Test Procedure | 3.4L | |
| Fuel Filter Location and R & I | REMOVAL PROCEDURE (MONTANA, SILHOUTTE, TRANS SPORT, VENTURE) | |
| Ignition | ||
| Firing Order & Cylinder Identification | See FIRING ORDER & CYLINDER IDENTIFICATION | |
| Ignition Wires (Resistance) | 600 per ft. | |
| Ignition Wires (Routing) & Coil Identification | See appropriate illustration under FIRING ORDER | |
| Spark Plug | ||
| Gap | .060 In. (1.52 mm) | |
| Torque | 20 Ft. Lbs. (27 N.m) | |
| Starting | ||
| Starter | NA | |
| Torque | TORQUE SPECIFICATIONS | |
| Wheel Alignment | ||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | |
| Torque | TORQUE SPECIFICATIONS | |
| Wheel & Tire | ||
| Wheel Lug Nut Torque | 100 Ft. Lbs. (136 N.m) | |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
