Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2000 Chevrolet LuminaFACTORY OEM SERVICE PROCEDURE
Anti-Lock Brake DTCS
ANTI-LOCK BRAKE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| Code | Definition |
|---|---|
| C1211 | ABS Warning Indicator Circuit Malfunction (Lumina) |
| C1213 | ABS Active Indicator Circuit Malfunction (Lumina) |
| C1214 | Electronic Brake Control Relay Contact Circuit Open |
| C1215 | Electronic Brake Control Relay Contact Circuit Active |
| C1216 | Electronic Brake Control Relay Coil Circuit Open |
| C1217 | Electronic Brake Control Relay Coil Circuit Shorted To Ground |
| C1218 | Electronic Brake Control Relay Coil Circuit Shorted To Voltage |
| C1221 | Left Front Wheel Speed Sensor Input Signal Equals Zero |
| C1222 | Right Front Wheel Speed Sensor Input Signal Equals Zero |
| C1223 | Left Rear Wheel Speed Sensor Input Signal Equals Zero |
| C1224 | Right Rear Wheel Speed Sensor Input Signal Equals Zero |
| C1225 | Left Front Excessive Wheel Speed Sensor Variation |
| C1226 | Right Front Excessive Wheel Speed Sensor Variation |
| C1227 | Left Rear Excessive Wheel Speed Sensor Variation |
| C1228 | Right Rear Excessive Wheel Speed Sensor Variation |
| C1232 | Left Front Wheel Speed Sensor Circuit Open Or Shorted (Lumina) |
| C1233 | Right Front Wheel Speed Sensor Circuit Open Or Shorted (Lumina) |
| C1234 | Left Rear Wheel Speed Sensor Circuit Open Or Shorted (Lumina) |
| C1235 | Right Rear Wheel Speed Sensor Circuit Open Or Shorted (Lumina) |
| C1236 | Low System Supply Voltage |
| C1237 | High System Supply Voltage |
| C1238 | Left Front ESB Will Not Hold Motor |
| C1241 | Right Front ESB Will Not Hold Motor |
| C1242 | Rear ESB Will Not Hold Motor |
| C1244 | Left Front ABS Channel Will Not Move |
| C1245 | Right Front ABS Channel Will Not Move |
| C1246 | Rear ABS Channel Will Not Move |
| C1247 | Left Front ABS Motor Free Spins |
| C1248 | Right Front ABS Motor Free Spins |
| C1251 | Rear ABS Motor Free Spins |
| C1252 | Left Front ABS Channel In Release Too Long |
| C1253 | Right Front ABS Channel In Release Too Long |
| C1254 | Rear ABS Channel In Release Too Long |
| C1255 | EBCM Internal Malfunction |
| C1256 | Left Front ABS Motor Circuit Open |
| C1257 | Left Front ABS Motor Circuit Shorted To Ground |
| C1258 | Left Front ABS Motor Circuit Shorted To Voltage |
| C1261 | Right Front ABS Motor Circuit Open |
| C1262 | Right Front ABS Motor Circuit Shorted To Ground |
| C1263 | Right Front ABS Motor Circuit Shorted To Voltage |
| C1264 | Rear ABS Motor Circuit Open |
| C1265 | Rear ABS Motor Circuit Shorted To Ground |
| C1266 | Rear ABS Motor Circuit Shorted To Voltage |
| C1276 | Left Front Solenoid Circuit Open Or Shorted To Ground |
| C1277 | Left Front Solenoid Circuit Shorted To Voltage |
| C1278 | Right Front Solenoid Circuit Open Or Shorted To Ground |
| C1281 | Right Front Solenoid Circuit Shorted To Voltage |
| C1282 | Calibration Malfunction |
| C1286 | EBCM Turned On BRAKE Warning Indicator |
| C1287 | BRAKE Warning Indicator Circuit Open Or Shorted To Voltage (Lumina) |
| C1291 | Open Brakelight Switch Circuit During Deceleration |
| C1292 | Open Brakelight Switch Circuit When ABS Was Required |
| C1293 | DTC C1291 Or C1292 Set In Current Or Previous Ignition Cycle |
| C1294 | Brakelight Switch Circuit Always Active |
| C1295 | Brakelight Switch Circuit Open |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
