Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1999 Chevrolet Tracker 4D Utility, RWD, AutomaticFACTORY OEM SERVICE PROCEDURE
Scan Tool Data
NOTE:
Information contained in the following tables is typical of readings taken on a vehicle with engine idling at normal operating temperature, throttle closed, transmission in Park or Neutral, system in closed loop status, and all accessories off (except as noted in table). For additional information, see scan tool owner's manual.
SCAN TOOL DATA VALUES
| Parameter | Units Displayed | Typical Value | |||
|---|---|---|---|---|---|
| Air Conditioning | On/Off | Off | |||
| BARO | kPa | 89-99 (Varies W/Barometric Pressure & Altitude) | |||
| Battery Voltage | Volts | 14 | |||
| Calculated IAC Air Flow | L/min | 125-155 | |||
| Closed Throttle Switch | Idle/Not Idle | Idle | |||
| Desired Idle Speed | RPM | 750 | |||
| ECT | °F (°C) | 176-194 (80-90) | |||
| EGR Duty Cycle | Percent | 0 | |||
| EGR Switch | Closed/Open | Closed | |||
| Engine Load | Percent | 10-18 | |||
| Engine Speed | RPM | 725-775 | |||
| EVAP Density Trim | Counts | Varies | |||
| EVAP Duty Cycle | Percent | 0-100 | |||
| EVAP Tank Pressure Control Solenoid | On/Off | Varies | |||
| EVAP Vent Solenoid | On/Off | Varies W/ECT | |||
| Fuel Cut-Off Signal | Yes/No | No | |||
| Fuel Level | Percent | Varies W/Fuel Level | |||
| Fuel Pump | On/Off | On | |||
| Fuel Tank Pressure | mm Hg | Varies | |||
| HO2S (Sensor 1) | Millivolts | 35-950 | |||
| HO2S (Sensor 2) | Millivolts | 35-950 | |||
| HO2S (Sensor 1) Ready | Yes/No | Yes | |||
| HO2S (Sensor 2) Ready | Yes/No | Varies | |||
| IAC Duty Cycle | |||||
| 1.6L | Percent | 17-30 | |||
| 2.0L | Percent | 20-40 | |||
| IAT | °F (°C) | Varies W/Underhood & Ambient Temp. | |||
| Injector PWM | Milliseconds | 2.7-4.3 | |||
| Long Term FT | Percent | Around 0 | |||
| Loop Status | Open/Closed | Closed | |||
| MAF | |||||
| 1.6L | Grams/Second | 1.1-2.9 | |||
| 2.0L | Grams/Second | 1.5-4.0 | |||
| MAP (Pressure) | kPa | 26-51 (Varies W/Barometric Pressure & Altitude) | |||
| MAP (Voltage) | Volts | 1.30-1.90 (Varies W/Barometric Pressure & Altitude) | |||
| PNP (A/T)(1) | P-N/R-D-L | P-N | |||
| Power Steering Switch | On/Off | Off (Wheels Straight) | |||
| Short Term FT | Percent | Around 0 | |||
| Spark | Degrees | 12-16 | |||
| Starter Switch | Released/Cranking | Released | |||
| Total Fuel Trim | Percent | Around 0 | |||
| TP Angle | Percent | 0 | |||
| TP Sensor | Volts | 0.50-0.80 | |||
| Vehicle Speed | km/h/MPH | 0 | |||
|
|||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
