Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1997 Chevrolet Venture LSFACTORY OEM SERVICE PROCEDURE
Torque Specifications
| Fastener | Specification |
|---|---|
| Delphi CS 144 (KG9) | |
| Generator Brush Holder Bolt/Screw | 22 In. lbs. (2.5 N.m) |
| Generator Capacitor/Rectifier Bridge Bolt/Screw | 22 In. lbs. (2.5 N.m) |
| Generator Front Brace Bolt/Screw | 37 Ft. lbs. (50 N.m) |
| Generator Front Brace Nut | 18 Ft. lbs. (25 N.m) |
| Generator Mounting Bracket Bolt/Screw | 37 Ft. lbs. (50 N.m) |
| Generator Output "BAT" Terminal Nut | 18 Ft. lbs. (25 N.m) |
| Generator Pivot Bolt/Screw | 37 Ft. lbs. (50 N.m) |
| Generator Pivot Nut | 37 Ft. lbs. (50 N.m) |
| Generator Rear Brace Bolt/Screw | 18 Ft. lbs. (25 N.m) |
| Generator Rear Brace Nut | 18 Ft. lbs. (25 N.m) |
| Generator Rectifier Bridge Bolt/Screw | 22 In. lbs. (2.5 N.m) |
| Generator Rectifier Bridge to Stud with Generator Battery Terminal Nut | 89 In. lbs. (10 N.m) |
| Generator Regulator Attaching Bolt/Screw | 22 In. lbs. (2.5 N.m) |
| Generator Rotor Shaft Drive End Nut | 74 Ft. lbs. (100 N.m) |
| Generator Stator Lead Attaching Nut | 22 In. lbs. (2.5 N.m) |
| Generator Through-Bolt/Screw | 49 In. lbs. (5.5 N.m) |
| Valeo A13VI+ (K68) | |
| Generator Front Brace Bolt/Screw | 37 Ft. lbs. (50 N.m) |
| Generator Front Brace Nut | 18 Ft. lbs. (25 N.m) |
| Generator Mounting Bracket Bolt/Screw | 37 Ft. lbs. (50 N.m) |
| Generator Output "BAT" Terminal Nut | 11 Ft. lbs. (15 N.m) |
| Generator Pivot Bolt/Screw | 37 Ft. lbs. (50 N.m) |
| Generator Pivot Nut | 37 Ft. lbs. (50 N.m) |
| Generator Rear Brace Bolt/Screw | 18 Ft. lbs. (25 N.m) |
| Generator Rear Brace Nut | 18 Ft. lbs. (25 N.m) |
| Generator Rear Cover Nut | 18 In. lbs. (2 N.m) |
| Generator Regulator/Brush Holder Nut | 27 In. lbs. (3 N.m) |
| Generator Regulator Terminal Bolt/Screw | 18 In. lbs. (2 N.m) |
| Generator Rotor Shaft Drive End Nut | 52 Ft. lbs. (70 N.m) |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.