Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1995 Chevrolet Lumina BaseFACTORY OEM SERVICE PROCEDURE
Torque Specifications
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) | |||||
|---|---|---|---|---|---|---|
| Crankshaft Position Sensor Bolt | ||||||
| 3.8L | 15-30 (20-41) | |||||
| Fuel Inlet & Return Line Nuts | ||||||
| 3.4L | 22 (30) | |||||
| 3.1L & 3.8L | 13 (17) | |||||
| Fuel Rail Retaining Bolts | ||||||
| 3.8L | 11 (15) | |||||
| Harmonic Balancer Bolt | ||||||
| 3.1L & 3.4L | 110 (149) | |||||
| 3.8L | (2) 110 (149) | |||||
| Intake Manifold Plenum Bolts | ||||||
| 3.1L | 18 (24) | |||||
| Oxygen Sensor | 30 (41) | |||||
| Throttle Body Bolts | ||||||
| 3.4L | (1) | |||||
| 3.1L | 18 (24) | |||||
| Upper Manifold Assembly Bolts | ||||||
| 3.4L | 18 (25) | |||||
| INCH Lbs. (N.m)Β | ||||||
| Camshaft Position Sensor Bolt | ||||||
| 3.1L & 3.4L | 89 (10) | |||||
| 3.8L | 35-53 (4.0-6.0) | |||||
| Crankshaft (3X) Position Sensor Bolt | ||||||
| 3.1L & 3.4L | 71 (8.0) | |||||
| Crankshaft (24X) Position Sensor Bolt | ||||||
| 3.1L & 3.4L | 89 (10) | |||||
| Fuel Line-To-Fuel Rail Retaining Bracket Screw | ||||||
| 3.4L | 27 (3.0) | |||||
| Fuel Pressure Regulator Screws | ||||||
| 3.1L | 75 (8.5) | |||||
| 3.4L | 84 (9.5) | |||||
| 3.8L | 89 (10) | |||||
| Fuel Rail Retaining Bolts | ||||||
| 3.1L & 3.4L | 89 (10) | |||||
| Idle Air Control (IAC) Valve Screw | ||||||
| All Models | 26 (3.0) | |||||
| Ignition Coil-To-Module Screws | 40 (4.5) | |||||
| Ignition Control Module/Coil Pack-To-Bracket Nuts | ||||||
| 3.8L | 71 (8.0) | |||||
| Throttle Body Bolts | ||||||
| 3.8L | 89 (10) | |||||
| Throttle Position Sensor Screw | 18 (2.0) | |||||
|
||||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
