Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1981 Chevrolet Hi-Cube Standard TransFACTORY OEM SERVICE PROCEDURE
General Motors
| Application | Axle Gap (Inches) (1) | Caster (Degrees) | Camber (Degrees) | Toe-In (Inches) | Steering Axis Inclin. (Degrees) | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| C10 | 2 1/2 | 2.4±1.0 | 0.2±0.7 | 3/16 | ..... | ||||||||||
| 2 3/4 | 2.1±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 | 1.8±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3/4 | 1.5±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 1/2 | 1.2±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 3/4 | 1.0±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 | 0.7±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 1/4 | 0.5±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 1/2 | 0.2±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 3/4 | 0.1±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 5 | 0.3±1.0 | 0.2±0.7 | 3.16 | ..... | |||||||||||
| C20 & 30 | 2 1/2 | 1.5±1.0 | 0.2±0.7 | 3/16 | ..... | ||||||||||
| 2 3/4 | 1.2±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 | 0.9±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 1/4 | 0.6±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 1/2 | 0.3±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 3/4 | 0.1±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 | 0±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 1/4 | -0.1±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 1/2 | -0.7±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 3/4 | -0.1±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 5 | -1.2±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| K10, 20 & 30 | 2 1/2 to 5 | 8(3) | 1.0(2)(3) | 0 | ..... | ||||||||||
| G10 & 20 | 1 1/2 | 3.5±1.0 | 0.5±0.7 | 3/16 | ..... | ||||||||||
| 1 3/4 | 3.3±1.0 | 0.5±0.7 | 3/16 | ..... | |||||||||||
| 2 | 3.1±1.0 | 0.5±0.7 | 3/16 | ..... | |||||||||||
| 2 1/4 | 2.9±1.0 | 0.5±0.7 | 3/16 | ..... | |||||||||||
| 2 1/2 | 2.7±1.0 | 0.5±0.7 | 3/16 | ..... | |||||||||||
| 2 3/4 | 2.6±1.0 | 0.5±0.7 | 3/16 | ..... | |||||||||||
| 3 | 2.4±1.0 | 0.5±0.7 | 3/16 | ..... | |||||||||||
| 3 1/4 | 2.2±1.0 | 0.5±0.7 | 3/16 | ..... | |||||||||||
| 3 1/2 | 2.1±1.0 | 0.5±0.7 | 3/16 | ..... | |||||||||||
| 3 3/4 | 1.9±1.0 | 0.5±0.7 | 3/16 | ..... | |||||||||||
| 4 | 1.8±1.0 | 0.5±0.7 | 3/16 | ..... | |||||||||||
| 4 1/4 | 1.6±1.0 | 0.5±0.7 | 3/16 | ..... | |||||||||||
| G30 | 1 1/2 | 2.8±1.0 | 0.2±0.7 | 3/16 | ..... | ||||||||||
| 1 3/4 | 2.5±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 2 | 2.2±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 2 1/4 | 1.9±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 2 1/2 | 1.6±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 2 3/4 | 1.3±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 | 0.1±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 1/4 | 0.7±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 1/2 | 0.5±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 3/4 | 0.2±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 | 0±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 1/4 | -0.2±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| P10 | 2 1/2 | 2.3±1.0 | 0.2±0.7 | 3/16 | ..... | ||||||||||
| 2 3/4 | 2.0±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 | 1.7±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 1/4 | 1.5±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 1/2 | 1.2±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 3/4 | 0.9±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 | 0.6±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 1/4 | 0.4±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 1/2 | 0.1±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 3/4 | -0.1±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 5 | -0.3±1.0 | 0.2±0.7 | 3/16 | ..... | |||||||||||
| P20 & 30 | 2 | 2.9±1.0(4)(4) | 0.2±0.7 | 3/16 | ..... | ||||||||||
| 2 1/4 | 2.6±1.0(4)(5) | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 2 1/4 | 2.3±1.0(4)(5) | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 2 3/4 | 2.0±1.0(4)(5) | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 | 1.7±1.0(4)(5) | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 1/4 | 1.4±1.0(4)(5) | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 1/2 | 1.2±1.0(4)(5) | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 3 3/4 | 0.9±1.0(4)(5) | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 | 0.6±1.0(4)(5) | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 1/4 | 0.4±1.0(4)(5) | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 1/2 | 0.2±1.0(4)(4) | 0.2±0.7 | 3/16 | ..... | |||||||||||
| 4 3/4 | 0.1±1.0(4)(5) | 0.2±0.7 | 3/16 | ..... | |||||||||||
|
NOTE:
The vehicle series and model application in this table has been abbreviated for common reference to both Chevrolet and GMC. Chevrolet models use numerical designations as listed; GMC models use numerical designations as follows; 1500 = 10; 2500=20; 3500 = 30.
|
|||||||||||||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
