Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1981 Chevrolet Chevette Scooter, Standard TransFACTORY OEM SERVICE PROCEDURE
Removal & Installation
WARNING: This page is about the Chevette Base, 2D Hatchback, 1.6L Eng VIN 9, Automatic Trans, Trans Mfr CD 180/MD3, which is a different variant/trim than selected.
TRANS ID - 180, 180C
| Applies To | Note | Standard Hours | Warranty Hours | Skill Level |
|---|---|---|---|---|
| 3.2 | 2.4 | C | ||
| Combination Procedure: CONVERTER: Drain & Test: | ||||
| 0.2 | 0.2 | C | ||
| Combination Procedure: FLYWHEEL: Remove & Replace: | ||||
| 0.2 | 0.2 | C | ||
| Combination Procedure: FRONT PUMP (REMOVED): Overhaul: | ||||
| 0.6 | 0.6 | B | ||
| Combination Procedure: FRONT PUMP BUSHING & SEAL: Remove & Replace: | ||||
| 0.3 | B | |||
| Combination Procedure: OIL PUMP: Remove & Replace: | ||||
| Front | 0.9 | 0.9 | B | |
| Combination Procedure: OIL PUMP SEAL: Remove & Replace: | ||||
| Front | 0.2 | B | ||
| Combination Procedure: TORQUE CONVERTER: Remove & Replace: | ||||
| 0.1 | C | |||
| Combination Procedure: TRANSMISSION ASSEMBLY: Replace: | ||||
| 0.6 | 0.3 | C | ||
TRANS ID - 200, 200C, 200-4R
| Applies To | Note | Standard Hours | Warranty Hours | Skill Level |
|---|---|---|---|---|
| 3.0 | 2.2 | C | ||
| Combination Procedure: CONVERTER: Drain & Test: | ||||
| 0.2 | 0.2 | C | ||
| Combination Procedure: FLYWHEEL: Remove & Replace: | ||||
| 0.2 | 0.2 | C | ||
| Combination Procedure: FRONT PUMP (REMOVED): Overhaul: | ||||
| 0.5 | 0.5 | B | ||
| Combination Procedure: FRONT PUMP BUSHING & SEAL: Remove & Replace: | ||||
| 0.3 | B | |||
| Combination Procedure: OIL PUMP: Remove & Replace: | ||||
| Front | 0.6 | 0.6 | B | |
| Combination Procedure: OIL PUMP SEAL: Remove & Replace: | ||||
| Front | 0.2 | B | ||
| Combination Procedure: TORQUE CONVERTER: Remove & Replace: | ||||
| 0.1 | C | |||
| Combination Procedure: TRANSMISSION ASSEMBLY: Replace: | ||||
| 0.6 | 0.3 | C | ||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.