Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2009 Cadillac CTS V, AutomaticFACTORY OEM SERVICE PROCEDURE
Engine Controls And Fuel - 6.2L - Introduction
- Specifications
- Schematic and Routing Diagrams
- Diagnostic Information and Procedures
- Repair Instructions
- Engine Control Module Replacement
- Crankshaft Position System Variation Learn
- Throttle Learn
- Engine Coolant Temperature Sensor Replacement
- Intake Air Temperature Sensor Replacement
- Mass Airflow Sensor with Intake Air Temperature Sensor Replacement
- Barometric Pressure Sensor Replacement
- Heated Oxygen Sensor Replacement - Bank 1 Sensor 1
- Heated Oxygen Sensor Replacement - Bank 1 Sensor 2
- Heated Oxygen Sensor Replacement - Bank 2 Sensor 1
- Heated Oxygen Sensor Replacement - Bank 2 Sensor 2
- Accelerator Pedal Position Sensor Replacement
- Throttle Body Assembly Replacement
- Throttle Body Cleaning
- Fuel Pressure Gage Installation and Removal
- Fuel Pressure Relief (Without CH 48027)
- Fuel Pressure Relief (With CH 48027)
- Metal Collar Quick Connect Fitting Service
- Plastic Collar Quick Connect Fitting Service
- Fuel Pump Flow Control Module Replacement
- Fuel Tank Draining
- Filler Tube Replacement
- Fuel Tank Replacement
- Fuel Tank Pressure Sensor Replacement
- Fuel Tank Fuel Pump Module Replacement - Right Side
- Fuel Level Sensor Replacement - Left Side
- Fuel Level Sensor Replacement - Right Side
- Fuel Hose/Pipes Replacement - Chassis
- Fuel Pressure Sensor Replacement
- Fuel System Cleaning
- Fuel Injection Fuel Rail Assembly Replacement
- Fuel Injector Replacement
- Fuel Injector Cleaning
- Evaporative Emission Canister Purge Solenoid Valve Replacement
- Evaporative Emission Canister Vent Solenoid Valve Replacement
- Evaporative Emission Canister Purge Tube Replacement
- Evaporative Emission System Hoses/Pipes Replacement
- Evaporative Emission Canister Replacement
- Ignition Coil Replacement
- Spark Plug Wire Inspection
- Spark Plug Wire Replacement
- Spark Plug Inspection
- Spark Plug Replacement
- Crankshaft Position Sensor Replacement
- Camshaft Position Sensor Replacement
- Knock Sensor 1 Replacement
- Knock Sensor 2 Replacement
- Air Cleaner Element Replacement
- Air Cleaner Assembly Replacement
- Air Cleaner Resonator Outlet Duct Replacement
- Supercharger Air Inlet Pressure Sensor Replacement
- Supercharger Air Outlet Pressure Sensor Replacement
- Charge Air Bypass Regulator Solenoid Valve Replacement
- Supercharger Bypass Valve Actuator Replacement
- Description and Operation
- Engine Control Module Description
- Throttle Actuator Control (TAC) System Description
- Fuel System Description
- Fuel Tank
- Electronic Returnless Fuel System (ERFS)
- Fuel Pump Flow Control Module (FPCM)
- Fuel Pressure Sensor
- On-Board Refueling Vapor Recovery (ORVR) System
- Fuel Tank Filler Pipe
- Fuel Filler Cap
- Modular Fuel Sender
- Fuel Pump
- Fuel Sender Strainers
- In-Line Fuel Filter
- EVAP Lines and Hoses
- Pressure Relief Valve (PRV)
- Fuel Rail
- Fuel Injectors
- Engine Fueling
- Sequential Fuel Injection (SFI)
- Clear Flood Mode
- Run Mode
- Acceleration Mode
- Deceleration Mode
- Battery Voltage Correction Mode
- Fuel Shut-Off Mode
- Evaporative Emission Control System Description
- Electronic Ignition System Description
- Boost Control System Description
- Special Tools and Equipment
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
