2006 Cadillac XLR VFACTORY OEM SERVICE PROCEDURE

Instrument Panel Module (IPM) - C1

WARNING: This page is about a different car, the 2006 Cadillac STS. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Instrument Panel Module (IPM) - C1 Connector
GM1468147Courtesy of GENERAL MOTORS CORP.
Computer/Integrating Systems Connector End Views

Connector Part Information 
  • OEM: 1318757-1
  • Service: 88988290
  • Description: 26-Way M 90 Series (NA)
Terminal Part Information 
  • Pins: 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 19, 20, 21, 22, 23, 25, 26
  • Terminal/Tray: 1123343-2/7
  • Core/Insulation Crimp: J/J
  • Release Tool/Test Probe: J-38125-24/J-35616-64B (L-BU)
  • Pins: 1, 2, 5, 6
  • Terminal/Tray: 7116-4020/11
  • Core/Insulation Crimp: E/C
  • Release Tool/Test Probe: 15315247/J-35616-18 (BK)
  • Pins: 3, 3
  • Terminal/Tray: 7116-4021/11
  • Core/Insulation Crimp: See Terminal Repair Kit
  • Release Tool/Test Probe: 15315247/J-35616-18 (BK)
Instrument Panel Module (IPM) - C1

Pin Wire Color Circuit No. Function
1 YE 32 Instrument Panel Lamp Fuse Supply Voltage (1)
2 YE 1491 Backlight Lamp Control
3 YE 6817 LED Backlight Dimming Control
3 YE 6817 LED Backlight Dimming Control
4 - - Not Used
5 WH 17 Stop Lamp Switch Signal
6 PK 3 Run/Crank Ignition 1 Voltage
7 - - Not Used
8 YE/BK 5728 ECM/TCM Serial Data Wake Up
9 YE 5727 High Speed GMLAN Serial Data Wake Up
10 PK 5722 Ignition Mode Switch LED Supply Voltage
11 D-GN 5525 Tap Up/Tap Down Enable Signal
12 WH 111 Hazard Switch Signal
13 BN 1356 Flash To Pass Switch Signal
14 BN/WH 301 Park Lamp Switch On Signal
15 L-GN 5724 Ignition Mode Switch Mode Control
16 D-BU 5719 Ignition Mode Switch Start LED Signal
17 L-GN 5720 Ignition Mode Switch Accessory LED Signal
18 - - Not Used
19 L-BU 6857 Headlamp Automatic High Beam Dim Status (TQ5)
20 L-BU 1134 Park Brake Switch Signal
21 PK/BK 1597 Interior Lamp Switch On Signal (w/o UV6)
22 PU 1783 Twilight Sentinel Delay Signal
23 WH 103 Headlamp Switch On Signal
24 - - Not Used
25 PU 1375 Remote Radio Control Head Accessory Supply Voltage
26 OG 5721 Ignition Mode Switch Off LED Signal
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.