Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Fastener Specifications
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|---|
| Application |
| Camshaft Position Actuator Solenoid Valve Seal |
| Camshaft Position Sensor Seal |
| Combustion Fuel Injector Seal |
| Engine Coolant Temperature Sensor Seal |
| Fuel Injector Wiring Harness Tie Strap |
| Fuel Pump Housing Seal |
| Fuel Sender Assembly Gasket |
| Fuel Tank Fuel Pump Module Gasket |
| Throttle Body Gasket |
| Turbocharger Air Pressure Sensor Seal |
| Vacuum Pump Gasket |
| Vacuum Pump Seal |
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|
|---|---|
| Application | Specification |
| Metric (English) | |
| Fuel Feed Intermediate Pipe/Fitting | 30 N.m (22 lb ft) |
| Fuel Injection Fuel Rail Fuel Pressure Sensor (In Sequence) | 32 N.m (24 lb ft) |
| Fuel Injector Bolt (In Sequence) | 5 N.m (44 lb in) |
| Fuel Pump Bolt (In Sequence) | 25 N.m (18 lb ft) |
|
NOTE:
All fasteners listed in this table can be reused after removal. |
|
|---|---|
| Application | Specification |
| Metric (English) | |
| Accelerator Pedal Position Sensor Fastener | 6 N.m (53 lb in) |
| Air Cleaner Outlet Duct Clamp | 3 N.m (27 lb in) |
| Camshaft Position Actuator Solenoid Valve Fastener | 10 N.m (89 lb in) |
| Camshaft Position Sensor Bolt | 10 N.m (89 lb in) |
| Charge Air Cooler Fastener | 10 N.m (89 lb in) |
| Charge Air Cooler Inlet Air Hose Bracket Bolt | 22 N.m (16 lb ft) |
| Charge Air Cooler Outlet Air Hose Bracket Bolt | 22 N.m (16 lb ft) |
| Charge Air Cooler Outlet Air Hose Bracket Nut | 22 N.m (16 lb ft) |
| Chassis Control Module Bolt | 9 N.m (80 lb in) |
| Crankshaft Position Sensor Bolt | 10 N.m (89 lb in) |
| Engine Oil Pressure Sensor | 35 N.m (26 lb ft) |
| Engine Wiring Harness Bracket Bolt | 9 N.m (80 lb in) |
| Engine Wiring Harness Ground Nut | 10 N.m (89 lb in) |
| Fuel Injection Fuel Feed Pipe Clip Bolt | 10 N.m (89 lb in) |
| Fuel Injection Fuel Rail Bolt (In Sequence) | 10 N.m (89 lb in) |
| Fuel Tank Filler Pipe Fastener | 9 N.m (80 lb in) |
| Fuel Tank Protector Fastener | 22 N.m (16 lb ft) |
| Fuel Tank Strap Fastener | 22 N.m (16 lb ft) |
| Heated Oxygen Sensor | 42 N.m (31 lb ft) |
| Ignition Coil Bolt | 10 N.m (89 lb in) |
| Intake Air Pressure and Temperature Sensor Fastener | 5 N.m (44 lb in) |
| Knock Sensor Fastener | 25 N.m (18 lb ft) |
| Mass Airflow Sensor Bolt | 5 N.m (44 lb in) |
| Parking Brake Cable Nut | 22 N.m (16 lb ft) |
| Spark Plug | 17 N.m (13 lb ft) |
| Throttle Body Bolt | 10 N.m (89 lb in) |
| Turbocharger Air Pressure Sensor Bolt | 3.8 N.m (34 lb in) |
| Turbocharger Bypass Valve Solenoid Bolt | 9 N.m (80 lb in) |
| Turbocharger Wastegate Actuator Nut | 10 N.m (89 lb in) |
| Turbocharger Wastegate Regulator Solenoid Valve Bolt | 8 N.m (71 lb in) |
| Underbody Cross Sill Shield Nut | 3.5 N.m (31 lb in) |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
No obligation. See pricing before you book.