Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Fastener Specifications
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|---|
| Application |
| Camshaft Position Actuator Solenoid Valve Seal |
| Camshaft Position Sensor Seal |
| Combustion Fuel Injector Seal |
| Engine Coolant Temperature Sensor Seal |
| Fuel Injector Wiring Harness Tie Strap |
| Fuel Pump Housing Seal |
| Fuel Sender Assembly Gasket |
| Fuel Tank Fuel Pump Module Gasket |
| Throttle Body Gasket |
| Turbocharger Air Pressure Sensor Seal |
| Vacuum Pump Gasket |
| Vacuum Pump Seal |
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|
|---|---|
| Application | Specification |
| Metric (English) | |
| Fuel Feed Intermediate Pipe/Fitting | 30 N.m (22 lb ft) |
| Fuel Injection Fuel Rail Fuel Pressure Sensor (In Sequence) | 32 N.m (24 lb ft) |
| Fuel Injector Bolt (In Sequence) | 5 N.m (44 lb in) |
| Fuel Pump Bolt (In Sequence) | 25 N.m (18 lb ft) |
|
NOTE:
All fasteners listed in this table can be reused after removal. |
|
|---|---|
| Application | Specification |
| Metric (English) | |
| Accelerator Pedal Position Sensor Fastener | 6 N.m (53 lb in) |
| Air Cleaner Outlet Duct Clamp | 3 N.m (27 lb in) |
| Camshaft Position Actuator Solenoid Valve Fastener | 10 N.m (89 lb in) |
| Camshaft Position Sensor Bolt | 10 N.m (89 lb in) |
| Charge Air Cooler Fastener | 10 N.m (89 lb in) |
| Charge Air Cooler Inlet Air Hose Bracket Bolt | 22 N.m (16 lb ft) |
| Charge Air Cooler Outlet Air Hose Bracket Bolt | 22 N.m (16 lb ft) |
| Charge Air Cooler Outlet Air Hose Bracket Nut | 22 N.m (16 lb ft) |
| Chassis Control Module Bolt | 9 N.m (80 lb in) |
| Crankshaft Position Sensor Bolt | 10 N.m (89 lb in) |
| Engine Oil Pressure Sensor | 35 N.m (26 lb ft) |
| Engine Wiring Harness Bracket Bolt | 9 N.m (80 lb in) |
| Engine Wiring Harness Ground Nut | 10 N.m (89 lb in) |
| Fuel Injection Fuel Feed Pipe Clip Bolt | 10 N.m (89 lb in) |
| Fuel Injection Fuel Rail Bolt (In Sequence) | 10 N.m (89 lb in) |
| Fuel Tank Filler Pipe Fastener | 9 N.m (80 lb in) |
| Fuel Tank Protector Fastener | 22 N.m (16 lb ft) |
| Fuel Tank Strap Fastener | 22 N.m (16 lb ft) |
| Heated Oxygen Sensor | 42 N.m (31 lb ft) |
| Ignition Coil Bolt | 10 N.m (89 lb in) |
| Intake Air Pressure and Temperature Sensor Fastener | 5 N.m (44 lb in) |
| Knock Sensor Fastener | 25 N.m (18 lb ft) |
| Mass Airflow Sensor Bolt | 5 N.m (44 lb in) |
| Parking Brake Cable Nut | 22 N.m (16 lb ft) |
| Spark Plug | 17 N.m (13 lb ft) |
| Throttle Body Bolt | 10 N.m (89 lb in) |
| Turbocharger Air Pressure Sensor Bolt | 3.8 N.m (34 lb in) |
| Turbocharger Bypass Valve Solenoid Bolt | 9 N.m (80 lb in) |
| Turbocharger Wastegate Actuator Nut | 10 N.m (89 lb in) |
| Turbocharger Wastegate Regulator Solenoid Valve Bolt | 8 N.m (71 lb in) |
| Underbody Cross Sill Shield Nut | 3.5 N.m (31 lb in) |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.