Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2012 Buick Regal BaseFACTORY OEM SERVICE PROCEDURE
Disc Brake Component Specifications
WARNING: This page is about a different car, the 2010 Pontiac G5 and 2010 Chevrolet Cobalt. However, it is still accessible from the selected car via links, so may be relevant.
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Front Brakes J41/JM4 | ||
|
1.0 mm | 0.039 in |
|
12.0 mm | 0.472 in |
|
256.00 mm | 10.079 in |
|
280.00 mm | 11.024 in |
|
22.0 mm | 0.87 in |
|
0.06 mm | 0.002 in |
|
1.50 mm | 0.059 in |
|
0.025 mm | 0.001 in |
|
22.75 mm | 0.896 in |
|
23.69 mm | 0.933 in |
| Front Brakes JL9 (With LNF) | ||
|
315.5 mm | 12.421 in |
|
24.0 mm | 0.945 in |
|
0.06 mm | 0.002 in |
|
1.50 mm | 0.059 in |
|
0.025 mm | 0.001 in |
|
24.2 mm | 0.952 in |
|
26.0 mm | 1.023 in |
| Front Brakes JL9 (Without LNF) | ||
|
296.00 mm | 11.653 in |
|
22.8 mm | 0.898 in |
|
0.06 mm | 0.002 in |
|
1.50 mm | 0.059 in |
|
0.025 mm | 0.001 in |
|
23.0 mm | 0.906 in |
|
26.0 mm | 1.023 in |
| Rear Brakes JL9 (With LNF) | ||
|
292.0 mm | 11.496 in |
|
18.0 mm | 0.709 in |
|
0.06 mm | 0.002 in |
|
1.50 mm | 0.059 in |
|
0.025 mm | 0.001 in |
|
18.2 mm | 0.717 in |
|
19.9 mm | 0.783 in |
| Rear Brakes JL9 (Without LNF) | ||
|
270.0 mm | 10.630 in |
|
11.8 mm | 0.465 in |
|
0.06 mm | 0.002 in |
|
1.50 mm | 0.059 in |
|
0.025 mm | 0.001 in |
|
12.0 mm | 0.472 in |
|
14.0 mm | 0.551 in |
| * All brake rotors have a discard dimension cast into them. Replace any rotor that does not meet this specification. After refinishing the rotor, replace any rotor that does not meet the minimum thickness specification. | ||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
