Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Engine - Variable Camshaft/Valve Controls - Repair (G30)
2023 BMW 530iSECTION Engine - Variable Camshaft/Valve Controls - Repair (G30)
- 11 36 Variable Camshaft Timing Control
- 11 36 130 Removing and installing/replacing both VANOS central valves, left (M550i xDrive, 2020-2022)
- Remove the sealing cap on the cylinder head of the cylinder bank 1
- Moving the crankshaft to the installation position to adjust the timings
- Checking the VANOS adjuster of cylinder bank 1
- Relieving the chain tensioner at cylinder bank 1 for checking or setting the valve timings
- Removing hydraulic chain tensioner of cylinder bank 1
- Preloading the timing chain of cylinder bank 1
- Fixing the engine in the installation position on cylinder 1 (set valve timings)
- Removing both left VANOS central valves
- Installing both VANOS central valves at left
- Removing the special tool to pretension the tinning chain at cylinder bank 1
- Installing the hydraulic chain tensioner of cylinder bank 1
- Install the sealing cap on the cylinder head of cylinder bank 1
- 11 36 658 Removing and installing/replacing both actuators (after vehicle diagnosis) (530i, 2017-2022, 530i xDrive, 2017-2022)
- 11 36 658 Removing and installing/replacing both actuators (after vehicle diagnosis) (530e PHEV, 2018-2020, 530e xDrive PHEV, 2018-2020)
- 11 36 658 Removing and installing/replacing both actuators (after vehicle diagnosis) (530e PHEV, 2021-2022, 530e xDrive PHEV, 2021-2022)
- 11 36 658 Removing and installing/replacing both actuators (540i, 2017-2020, 540i, 2021-2022, 540i xDrive, 2021-2022)
- 11 36 658 Removing and installing/replacing both actuators (after vehicle diagnosis) (540i xDrive, 2017-2020)
- 11 36 730 Removing and installing/replacing VANOS solenoid actuator, left (With job no. 11 36 008) (M550i xDrive, 2018-2019)
- 11 36 730 Removing and installing/replacing VANOS solenoid actuator, left (With job no. 11 36 008) (M550i xDrive, 2020-2022)
- 11 36 731 Removing and installing/replacing the VANOS solenoid actuator, left (With job no. 11 36 008) (M550i xDrive, 2020-2022)
- 11 36 732 Remove and install/replace both left actuators (With job no. 11 36 008) (M550i xDrive, 2020-2022)
- 11 36 733 Removing and installing/replacing VANOS solenoid actuator, right (With job no. 11 36 008) (M550i xDrive, 2020-2022)
- 11 36 734 Removing and installing/replacing VANOS solenoid actuator, right (With job no. 11 36 008) (M550i xDrive, 2020-2022)
- 11 36 735 Removing and installing/replacing both actuators, right (With job no. 11 36 008) (M550i xDrive, 2018-2019)
- 11 36 735 Removing and installing/replacing both actuators, right (With job no. 11 36 008) (M550i xDrive, 2020-2022)
- 11 36 130 Removing and installing/replacing both VANOS central valves, left (M550i xDrive, 2020-2022)
- 11 37 VALVETRONIC
- 11 37 005 Removing and installing/replacing eccentric shaft (530i, 2017-2022, 530i xDrive, 2017-2022)
- 11 37 005 Removing and installing/replacing eccentric shaft (530e PHEV, 2018-2020, 530e xDrive PHEV, 2018-2020)
- 11 37 005 Removing and installing/replacing eccentric shaft (530e PHEV, 2021-2022, 530e xDrive PHEV, 2021-2022)
- 11 37 005 Removing and installing/replacing eccentric shaft (540i, 2017-2020, 540i, 2021-2022)
- 11 37 005 Removing and installing/replacing eccentric shaft (540i, 2021-2022 48V)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.