Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSBMW2021X6 M COMPETITIONREPAIR AND DIAGNOSISENGINE PERFORMANCEIGNITION SYSTEMENGINE ELECTRICAL SYSTEM -- REPAIR (F96)
2021 BMW X6 M Competition
Engine Electrical System -- Repair (F96)
2021 BMW X6 M CompetitionSECTION Engine Electrical System -- Repair (F96)
- 12 00 General Information
- 12 12 Spark Plugs
- 12 13 Ignition Coils
- 12 14 Crankshaft Sensor, Camshaft Sensor, Knock Sensor, Engine Control Module
- 12 14 512 Replace left exhaust camshaft sensor (after vehicle diagnosis) (X6 M 2020-2023)
- 12 14 513 Replace right exhaust camshaft sensor (after vehicle diagnosis) (X6 M 2020-2023)
- 12 14 521 Replacing the crankshaft sensor (after vehicle diagnosis) (X6 M 2020-2023)
- 12 14 522 Replace left intake camshaft sensor (after vehicle diagnosis) (X6 M 2020-2023)
- 12 14 526 Replace right intake camshaft sensor (after vehicle diagnosis) (X6 M 2020-2023)
- 12 14 555 Replacing the engine control module (DME), cylinder 1-4 (after vehicle diagnosis) (X6 M 2020-2023)
- 12 14 556 Replacing the engine control module (DME), cylinder 5-8 (after vehicle diagnosis) (X6 M 2020-2023)
- 12 14 610 Replacing knock sensor(s) right (X6 M 2020-2023)
- 12 14 611 Replace the left knock sensor(s) (after vehicle diagnosis) (X6 M 2020-2023)
- 12 14 700 Coding the control unit (DME) (X6 M 2020-2023)
- 12 14 705 Programming the control unit (DME) (X6 M 2020-2023)
- 12 31 Alternator
- 12 32 Voltage Regulator For Alternator
- 12 41 Starter Motor
- 12 42 Starter Motor Positive Battery Cable
- 12 51 Wiring Harness For Engine And Transmission
- 12 51 245 Remove and install/replace transmission module engine wiring, (X6 M 2020-2023)
- 12 51 300 Remove and install/replace engine wiring harness section, ignition module cylinder 1-4 (X6 M 2020-2023)
- 12 51 301 Remove and install/replace engine wiring harness section, ignition module cylinder 5-8 (X6 M 2020-2023)
- 12 51 302 Remove and install/replace wiring harness section, sensor system module cylinder 1-4 (X6 M 2020-2023)
- 12 51 303 Remove and install/replace wiring harness section, sensor system module cylinder 5-8 (X6 M 2020-2023)
- 12 51 304 Remove and install/replace wiring harness section of the Valvetronic servomotor of cylinders 1-4 (X6 M 2020-2023)
- 12 51 305 Remove and install/replace wiring harness section of the Valvetronic servomotor of cylinders 5-8 (X6 M 2020-2023)
- 12 51 321 Removing and installing/replacing adapter between the wiring harness section and the oil level sensor (X6 M 2020-2023)
- 12 51 322 Removing and installing/replacing wiring harness section of the engine control module (DME/PDM) (X6 M 2020-2023)
- 12 51 323 Removing and installing/replacing adapter between the wiring harness section and the oil temperature sensor (X6 M 2020-2023)
- 12 52 ECM Holder
- 12 61 Oil Pressure Switch, Oil Level Sensor
- 12 63 Power Distribution Box
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.