Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSBMW2013X6 MREPAIR AND DIAGNOSISENGINE PERFORMANCEENGINE CONTROL SYSTEMSENGINE - REPAIR
2013 BMW X6 M
Engine - Repair
2013 BMW X6 MSECTION Engine - Repair
- Engine, General
- 31 10 001 Completely removing and installing front axle with engine and transmission (N63/S63 E70/E71)
- 00 Danger of poisoning if oil is ingested/absorbed through the skin
- 11 00 000 Differences among basic engine versions (N63/S63)
- Engine identification
- 11 00... Overview of consumables (Electronic Parts Catalogue)
- 11 00 598 Removing and installing engine on front axle E70 E71 (N63/S63)
- 00 Risk of injury if oil comes into contact with eyes and skin
- 00 Safety information for working on vehicles with automatic engine start-stop function (MSA)
- 00 Safety instructions for handling oil
- 11 00 670 Securing engine in installation position (S63)
- 11 00... Service - engine oil (S63)
- Cylinder Head And Cylinder Head Cover
- 11 12 729 Checking cylinder head for water leaks (S63)
- 11 12 105 Removing and installing left cylinder head (S63)
- 11 12 106 Removing and installing right cylinder head (S63)
- 11 12 005 Removing and installing/sealing left cylinder head cover (S63)
- 11 12 006 Removing and installing/sealing right cylinder head cover (S63)
- Oil Sump
- Housing Cover
- 11 14 110 Removing and installing lower timing case cover (S63)
- 11 14 080 Removing and installing timing case cover, top left (S63)
- 11 14 085 Removing and installing timing case cover, top right (S63)
- 11 14 250 Removing and installing/sealing rear coolant end cover (N63)
- 11 14 151 Replacing crankshaft radial seal on transmission side (S63)
- 11 14 141 Replacing radial shaft seal in lower timing case cover (S63)
- Crankshaft With Bearing
- Flywheel
- Vibration Damper
- Piston With Rings And Pin
- V-Ribbed Belt With Tension Deflection Element
- Camshaft
- 11 31 573 Adjusting camshaft timing on left side (S63)
- 11 31 574 Adjusting camshaft timing on right side (S63)
- 11 31 070 Checking camshaft timing on left side (S63)
- 11 31 071 Checking camshaft timing on right side (S63)
- 11 31 032 Remove and install/replace left intake camshaft (S63)
- 11 31 038 Removing and installing/renewing right exhaust camshaft (S63)
- 11 33 052 Removing and installing/replacing all rocker arms on left side (S63)
- 11 31 036 Removing and installing/replacing left exhaust camshaft (S63)
- 11 31 034 Removing and installing/replacing right inlet camshaft (S63)
- 11 33 054 Removing and installing/replacing rocker arms on right side (S63)
- 11 31 094 Removing hydraulic chain tensioner for timing chains on left side (S63)
- 11 31 095 Removing hydraulic chain tensioner for timing chains on right side (S63)
- 11 31 052 Replacing both timing chains (S63)
- Rocker Arm With Bearing Mount
- Valves With Springs
- Variable Camshaft Timing
- 11 31 573 Adjusting camshaft timing on left side (S63)
- 11 31 574 Adjusting camshaft timing on right side (S63)
- 11 31 070 Checking camshaft timing on left side (S63)
- 11 31 071 Checking camshaft timing on right side (S63)
- 11 36 715 Removing and installing/replacing both solenoid valves on left side (S63)
- 11 36 720 Removing and installing/replacing both solenoid valves on right side (S63)
- 11 36 047 Removing and installing/replacing inlet and exhaust adjustment units on left side (S63)
- 11 36 048 Removing and installing/replacing inlet and exhaust adjustment units on right side (S63)
- Oil Pump With Filter And Drive
- Oil Filter And Lines
- Water Pump With Drive
- Thermostat And Connections
- Intake Manifold
- Supercharger With Control
- 11 65 Connection diagram, vacuum activation (S63)
- 11 65 714 Removing and installing/renewing electric changeover valve on exhaust turbocharger, right (S63)
- 11 65 025 Removing and installing/renewing exhaust turbocharger, right, cylinders 1-4 (S63)
- 11 65 185 Removing and installing/renewing heat shield at bottom (S63)
- 11 65 712 Removing and installing/replacing electric changeover valve on exhaust turbocharger, left (S63)
- 11 65 030 Removing and installing/replacing exhaust turbocharger, left, cylinders 5-8 (S63)
- 11 65 180 Removing and installing/replacing heat shield at top (S63)
- 11 61 065 Removing and installing/replacing left intake plenum (S63)
- 11 65 010 Removing and installing/replacing pressure accumulator (S63)
- 11 61 068 Removing and installing/replacing right intake plenum (S63)
- Vacuum Pump
- Valve For Exhaust Gas RECIRCULATION
- Emission Control, Oxygen Sensor
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.