Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2000 BMW M5FACTORY OEM SERVICE PROCEDURE
Specifications Index
M5 SPECIFICATIONS INDEX
| System | Specification/Procedure | |
|---|---|---|
| Air Conditioning | ||
| Service | HEATING AND AIR CONDITIONING - TECHNICAL DATA | |
| Torque | HEATING AND AIR CONDITIONING - TIGHTENING TORQUES | |
| Axle Nut/Hub Nut | ||
| Rear | 221 Ft. Lbs. (300 N.m) | |
| Brakes | ||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | |
| Disc Brakes | DISC BRAKE SPECIFICATIONS | |
| Torque | TORQUE SPECIFICATIONS | |
| Charging | ||
| Generator | GENERATOR SPECIFICATIONS | |
| Torque | TORQUE SPECIFICATIONS | |
| Drive Belts | ||
| Adjustment | ADJUSTMENTS | |
| Belt Routing | DRIVE BELT ROUTING | |
| Engine Cooling | ||
| General Service Specifications | SPECIFICATIONS | |
| Radiator Cap Pressure | 21.75 psi (150 kPa) Pressure is approximate and may vary slightly by vehicle. See cap top for specification. |
|
| Thermostat R & I | THERMOSTAT AND CONNECTIONS | |
| Water Pump R & I | WATER PUMP WITH DRIVE | |
| Engine Mechanical | ||
| Compression | ENGINE COMPRESSION | |
| Oil pressure | Oil pressure should be more than 7 psi (48 kPa) at idle and 65 psi (448 kPa) at 6500 RPM. | |
| Overhaul | ENGINE - TECHNICAL DATA | |
| Torque | ENGINE - TIGHTENING TORQUES | |
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |
| Flywheel/Flex Plate Torque | 77 Ft. Lbs. (105 N.m) | |
| Fuel System | ||
| Fuel Filter Location | Under vehicle, forward from fuel tank along fuel feed line behind fuel filter cover. | |
| Fuel Filter R & I | FUEL FILTER | |
| Pressure Release Procedure | FUEL SYSTEM PRESSURE RELEASE | |
| Pressure Specification | 50 psi (344 kPa) | |
| Fuel Pressure Test Procedure | FUEL VOLUME & PRESSURE | |
| Ignition | ||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER INDENTIFICATION | |
| Ignition Wires (Routing) | Coil on plug | |
| Spark Plug | ||
| Type | NGK BKR 6 EQUP (High Power) | |
| Gap | Spark plug gap is not adjustable. | |
| Torque | M12 x 1.25: 15-19 Ft. Lbs. (20-26 N.m) M14 x 1.25: 20-24 Ft. Lbs. (27-33 N.m) |
|
| Starting | ||
| Starter | STARTER SPECIFICATIONS | |
| Torque | TORQUE SPECIFICATIONS | |
| Wheel Alignment | ||
| Adjustment Specifications | ALIGNMENT SPECIFICATIONS E39 | |
| Torque | TORQUE SPECIFICATIONS E39 | |
| Wheel & Tire | ||
| Wheel Lug Nut Torque | 81.1-95.5 Ft. Lbs. (110-130 N.m) | |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
