Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Front Peripheral Camera -R243- CALIBRATING
Special Tools And Workshop Equipment Required
- Calibration Tool :VAS6350
- Peripheral Camera Calibration Device :VAS6350/6
- Vehicle Diagnostic Tester
The Front Peripheral Camera -R243- is installed in the bumper cover between the Audi rings (between Night Vision System Camera -R212- and Garage Door Opener Control Module -J530-).
-- Set-up requirements Calibration Tool .
-- Install and align the :VAS6350 with : VAS6350/6 . Refer to Calibration Tool .
-- Connect the Vehicle Diagnostic Tester.
Setting Up The Calibration Device
:VAS6350/1 installing:
-- Check the dimension of the holes.
-- Equip the :VAS6350/1 appropriately.
-- To do so, secure three wheel bolt adapters in the hole circle to each :VAS6350/1 .
-- Place the paddle on both :VAS6350/1 and secure them using a clamping screw.
-- Place the :VAS6350/1 onto the wheel bolts on the rear wheels.
The :VAS6350/1 are positioned by the "O rings" in the adapters and held in place.
Attach the :VAS6350/1 onto the wheels so that any installed "anti-theft" wheel mounting bolts are not connected to the :VAS6350/1 .
-- Adjust the paddle with aid of lock bolts so that they move freely just above the floor. Make sure that the paddle is easily accessible.
:VAS6350 with :VAS6350/6 Orientation
-- Position the :VAS6350 with the :VAS6350/6 -1- at a distance of between 400 mm and 600 mm -dimension A- in front of the vehicle in the center (in front of the front bumper trim).
-- Bring the : VAS6350 with :VAS6350/6 into a horizontal position.
-- To do so, twist plastic feet under the calibration field of the :VAS6350 so that air bubble in level is located exactly in the center of the indicator -arrow-
Make sure light does not reflect off the :VAS6350/6 .
Reflections affect the camera and may make it impossible to perform the calibration.
-- Attach the :VAS6350/3 -4- to the :VAS6350/6 to the center of the location provided.
-- Switch on the :VAS6350/3 -4- and align the calibration field of the :VAS6350 with :VAS6350/6 so that the laser beam points at the front of the vehicle, in the center just above the Audi rings.
-- Make sure the Audi rings are exactly in the center. Correct the laser beam accordingly.
Distance Measurement
-- Switch on the :VAS6350/2 .
The display shows how to stop the :VAS6350/2 . Press the corresponding button.
- Attach with front edge
- Attach with rear edge
-- Hold the :VAS6350/2 -2- flush in the bracket on one side of the :VAS6350 calibration field (with rear edge). To do so, the :VAS6350/2 -2- must sit securely on the bracket.
-- Press the measuring button briefly.
The laser turns on.
-- Make sure that laser beam from :VAS6350/2 -2- hits lower, enlarged part of paddle -1-.
If this is not the case, paddles must be corrected accordingly via clamping screws on the :VAS6350/1 .
-- Use one hand to secure the :VAS6350/2 in the bracket on the calibration field :VAS6350 while the laser beam is visible on the paddle.
-- Then press the measuring button for distance measurement briefly.
-- Repeat this measurement on the other side of the :VAS6350 calibration field in the same way for the rear wheel.
The distance value must be the same on both sides.
If values are not identical:
-- Align the :VAS6350 with the :VAS6350/6 long enough so that both sides are identical.
Pay attention when aligning the :VAS6350 with :VAS6350/6 that the :VAS6350/3 from the :VAS6350/6 strikes the center of the Audi rings and the indicator of the level remains centered. Adjust if necessary.
-- Make note of the distance dimension measured.
Dimension Measurement -h-
-- Measure the height of the :VAS6350 -2- calibration field, dimension -h-, from the surface of the :VAS6350 -2- calibration field (not the aluminum frame) down to the floor. Measure the hole in the :VAS6350 -2- calibration field.
Make sure the :VAS6350/2 -1- is adjusted correctly (attach with front edge).
The display shows how to stop the :VAS6350/2 . Press the corresponding button.
- Attach with front edge
- Attach with rear edge
Dimension -h- and the distance dimension must now be entered into the Vehicle Diagnostic Tester in "millimeters".
Performing Calibration
Vehicle Diagnostic Tester is attached.
-- Select the Diagnostic mode and start the diagnostics.
-- Select the tab Test Plan .
-- Select Select Individual Tests and choose the following sequence.
- Body
- Electrical Equipment
- 01 - OBD-capable systems
- 6C - Peripheral Camera Control Module | J928
- 6C - Peripheral Camera Control Module, Functions
- 6C - Calibration, (Repair Group 91)
The Vehicle Diagnostic Tester continues with the calibrating procedure from here on.
Make sure light does not reflect off the :VAS6350/6 .
Reflections affect the camera and may make it impossible to perform the calibration.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
