Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2014 Audi S7FACTORY OEM SERVICE PROCEDURE
Headlamp Control Module: Remove & Replace
| Applies To | Note | Standard Hours | Warranty Hours | Skill Level |
|---|---|---|---|---|
| HID Headlamps,Daytime Running and Parking /Position Lamp Module,Both,J860/J861 | Includes: Additional time for use of scan tool to perform this procedure. | 1.6 | B | |
| HID Headlamps,Daytime Running and Parking /Position Lamp Module,One Side,J860/J861 | Includes: Additional time for use of scan tool to perform this procedure. | 1.1 | B | |
| HID Headlamps,HID Control Module,Both,J343/J344 | Includes: Additional time for use of scan tool to perform this procedure. | 1.6 | B | |
| HID Headlamps,HID Control Module,One Side,J343/J344 | Includes: Additional time for use of scan tool to perform this procedure. | 1.1 | B | |
| HID Headlamps,Power Output Module,Both,J667/J668 | Includes: Additional time for use of scan tool to perform this procedure. | 1.6 | B | |
| HID Headlamps,Power Output Module,One Side,J667/J668 | Includes: Additional time for use of scan tool to perform this procedure. | 1.1 | B | |
| LED,Daytime Running and Parking /Position Lamp Module,Both,A29/A33,#3 | Includes: Additional time for use of scan tool to perform this procedure. | 1.6 | B | |
| LED,Daytime Running and Parking /Position Lamp Module,One Side,A29/A33,#3 | Includes: Additional time for use of scan tool to perform this procedure. | 1.1 | B | |
| LED,High Beam/Cornering Lamp Module,Both,A28/A32,#2 | Includes: Additional time for use of scan tool to perform this procedure. | 1.6 | B | |
| LED,High Beam/Cornering Lamp Module,One Side,A28/A32,#2 | Includes: Additional time for use of scan tool to perform this procedure. | 1.1 | B | |
| LED,Low Beam Module,Both,A27/A31,#1 | Includes: Additional time for use of scan tool to perform this procedure. | 1.6 | B | |
| LED,Low Beam Module,One Side,A27/A31,#1 | Includes: Additional time for use of scan tool to perform this procedure. | 1.1 | B | |
| Range | Includes: Additional time for use of scan tool to perform this procedure. | 1.0 | B | |
| Combination Procedure: ADAPTIVE CRUISE CONTROL SYSTEM: Calibrate: DOES NOT include wheel alignment (unless noted otherwise). | ||||
| Includes: Additional time for use of scan tool to perform this procedure. | 1.5 | B | ||
| Combination Procedure: NIGHT VISION SYSTEM: Calibrate: DOES NOT include wheel alignment (unless noted otherwise). | ||||
| Includes: Additional time for use of scan tool to perform this procedure. | 1.0 | B | ||
| Combination Procedure: PERIPHERAL CAMERA: Calibrate: DOES NOT include wheel alignment (unless noted otherwise). | ||||
| Includes: Additional time for use of scan tool to perform this procedure. | 1.0 | B | ||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.