Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Specifications Index
& Procedures >> Specifications Index Specifications Index SPECIFICATIONS INDEX System Specification/Procedure Air Conditioning Service DIAGNOSIS AND TESTING REFRIGERANT R134A CAPACITIES Torque FASTENER TIGHTENING SPECIFICATIONS Axle Nut/Hub Nut Front WHEEL BEARING HOUSING AND WHEEL BEARING UNIT Rear WHEEL BEARING HOUSING, WHEEL BEARING UNIT, TRAILING ARM WITH MOUNTING BRACKET AND STONE DEFLECTOR OVERVIEW Battery BATTERY, TESTING Brakes Bleeding Sequence BRAKE SYSTEM, BLEEDING WITH VAS 5234 AND VAS 5234/1A Disc Brakes 00 GENERAL, TECHNICAL DATA Torque 46 MECHANICAL COMPONENTS 47 HYDRAULIC COMPONENTS Charging Generator NA Torque 2.0L GENERATOR - ENGINE CODE(S): BPY, CBFA & CCTA 3.2L GENERATOR - ENGINE CODE(S): BUB & CBRA Drive Belts Adjustment & Belt Routing 2.0L RIBBED BELT 3.2L RIBBED BELT Engine Cooling General Service Specifications 2.0L COOLING SYSTEM, DRAINING AND FILLING for BPY engines COOLING SYSTEM, DRAINING AND FILLING for CBEA COOLING SYSTEM, DRAINING AND FILLING for CBFA & CCTA 3.2L COOLING SYSTEM, DRAINING AND FILLING for BUB & CBRA Radiator Cap Pressure 1.4-1.6 Bar Thermostat R & I 2.0L COOLANT DISTRIBUTION HOUSING WITH MAP CONTROLLED ENGINE COOLING THERMOSTAT 3.2L COOLANT THERMOSTAT Water Pump R & I 2.0L COOLANT PUMP for BPY Engines COOLANT PUMP for CBEA Engines COOLANT PUMP for CBFA & CCTA Engines 3.2L COOLANT PUMP Engine Mechanical 2.0L Compression COMPRESSION, CHECKING for BPY engines COMPRESSION PRESSURE, CHECKING for CBFA & CCTA engines Oil Pressure At 2000 RPM & 80°C: 2.7 to 4.5 Bar Overhaul 13 CRANKSHAFT, CYLINDER BLOCK for BPY engines 13 CRANKSHAFT, CYLINDER BLOCK for CBFA & CCTA engines Torque See Appropriate Procedure 3.2L Compression COMPRESSION, CHECKING Oil Pressure At Idle: Min.2.0 Bar At 2000 RPM: min.3.0 Bar Overhaul 13 CRANKSHAFT, CYLINDER BLOCK Torque See Appropriate Procedure Fluid Specifications See FLUIDS under MAINTENANCE tab. Engine Oil Pan Drain Plug 30 Nm Flywheel/Flex Plate Torque 60 Nm + 90° Fuel System Pressure Specification 2.0L Approx: 6.0 Bar (Before high-pressure pump) 3.2L Approx: 4.0 Bar Fuel Pressure Test Procedure 2.0L FUEL PRESSURE AND RESIDUAL PRESSURE BEFORE HIGH PRESSURE PUMP, CHECKING for BPY engine FUEL PRESSURE AND RESIDUAL PRESSURE BEFORE HIGH PRESSURE PUMP, CHECKING for CBFA & CCTA engines 3.2L SYSTEM PRESSURE, FUEL PRESSURE REGULATOR AND RESIDUAL PRESSURE, CHECKING Ignition Firing Order & Cylinder Identification 2.0L FIRING ORDER & CYLINDER INDENTIFICATION 3.2L FIRING ORDER & CYLINDER INDENTIFICATION Ignition Wires (Resistance) Coil-On-Plug Ignition Wires (Routing) Coil-On-Plug Spark Plug 2.0L SPARK PLUGS, REMOVING AND INSTALLING 3.2L TEST DATA, SPARK PLUGS Starting Starter/Torque STARTER - ENGINE CODE(S): BPY, CBFA & CCTA STARTER - ENGINE CODE(S): BUB, CBRA Wheel Alignment Adjustment Specifications WHEEL ALIGNMENT SPECIFICATIONS Torque WHEEL ALIGNMENT SPECIFICATIONS Wheel & Tire Wheel Lug Nut Torque 120 Nm
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.