Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1993 Audi S4 2.2 PFACTORY OEM SERVICE PROCEDURE
Checking Control Signal
- Disconnect EVAP canister purge regulator valve harness connector.
- Connect (US 1115 LED) tester (using VW 1594 connector test kit), between terminal No. 2 of EVAP canister purge regulator valve harness, and engine ground. See Figure.
- Operate starter for a few seconds. LED tester must light up.
- If NO: Check the following items in the electronics box and repair as necessary:
- Injector valve circuit breaker S72 okay.
- EVAP frequency valve circuit breaker S75 okay.
- Check continuity between terminal No. 2 of EVAP canister purge regulator valve harness, and EVAP frequency valve circuit breaker S75. Resistance must be 0.5 ohm maximum.
- Check continuity between EVAP frequency valve circuit breaker S75, and terminal No. 31 of fuel pump relay -J17-, relay position 6. See Figure. Resistance must be 0.5 ohm maximum.
- Check control signal to fuel pump relay. See FUEL PUMP RELAY CONTROL SIGNAL .
- Reconnect LED tester, between terminal No. 2 of EVAP canister purge regulator valve harness, and engine ground. See Figure.
- Initiate Output Diagnostic Test Mode (DTM). See OUTPUT DIAGNOSTIC TEST MODE (DTM) in SELF-DIAGNOSTICS
article. LED tester must light up.NOTE: Positive (+) voltage must be available at terminal No. 2 of harness connector regardless of which Output DTM is called up.
- If LED tester does NOT light up, connect (VAG 1598) test box, using (VAG 1598/5) adapter cable to ECM. See CONNECTING VAG 1598 TEST BOX . ECM remains disconnected.
- Check continuity between terminal No. 2 of EVAP canister purge regulator valve harness connector, and test box terminal 37, using wiring diagram. Resistance must be 0.5 ohm maximum. See WIRING DIAGRAMS .
- If circuit is open: Repair wiring between terminal No. 37 of ECM connector, and terminal No. 2 of EVAP canister purge regulator valve connector. See Figure.
- If continuity is OK, replace ECM. After replacement of ECM, see ECM IDENTIFICATION and ECM CODING under SELF-DIAGNOSTIC SYSTEM in SELF-DIAGNOSTICS article.
- Remove test box and adapter cable. Reconnect ECM to vehicle wiring harness.
- Connect LED tester to terminals No. 1 and 2 of EVAP canister purge regulator valve harness connector.
- Initiate Output Diagnostic Test Mode (DTM). See OUTPUT DIAGNOSTIC TEST MODE (DTM) in SELF-DIAGNOSTICS article. LED tester must blink when valve is activated.
- If LED tester does not blink, connect (VAG 1598) test box, using (VAG 1598/5) adapter cable to ECM. See CONNECTING VAG 1598 TEST BOX . ECM remains disconnected.
- If LED tester lights up continuously: Check wiring (using wiring diagram) between terminal No. 1 of EVAP canister purge regulator valve harness and test box terminal 5 for short circuit to ground. See WIRING DIAGRAMS .
- If LED tester does NOT blink: Check continuity between terminal No. 1 of EVAP canister purge regulator valve harness connector, and test box terminal 5. Resistance must be 1.0 ohm maximum.
- If circuit is grounded or open between terminal No. 1 of EVAP canister purge regulator valve connector, and terminal 5 of ECM connector. See Figure. Repair as necessary.
- If circuit is OK: Replace ECM. See ECM IDENTIFICATION and ECM CODING under SELF-DIAGNOSTIC SYSTEM in SELF-DIAGNOSTICS article.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
