Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1984 Audi QuattroFACTORY OEM SERVICE PROCEDURE
Wheel Alignment Specifications
WHEEL ALIGNMENT SPECIFICATIONS
| Application | Specification | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Coupe GT, 4000S | |||||||||||
| Front | |||||||||||
| W/Link Rod | |||||||||||
| Caster (Degrees) | (2) +1 +/- 2 | ||||||||||
| Camber (Degrees) | -1/6 to -1 1/6 | ||||||||||
| Toe-in (Inches) | (1) 0 to 1/3 | ||||||||||
| Toe-Out on Turns (Degrees) | |||||||||||
| Inner | 20 3/4 | ||||||||||
| Outer | 20 | ||||||||||
| W/O Link Rod | |||||||||||
| Caster (Degrees) | (2) 0 to 1 | ||||||||||
| Camber (Degrees) | -1/6 to -1 1/6 | ||||||||||
| Toe-in (Inches) | (1) 0 to 1/3 | ||||||||||
| Toe-Out on Turns (Degrees) | |||||||||||
| Inner | 20 3/4 | ||||||||||
| Outer | 20 | ||||||||||
| Rear | |||||||||||
| Caster (Degrees) | (2) | ||||||||||
| Camber (Degrees) | -1 1/3 to -2/3 | ||||||||||
| Toe-in (Inches) | (1) 0 to 2/3 | ||||||||||
| Toe-Out on Turns (Degrees) | |||||||||||
| Inner | N/A | ||||||||||
| Outer | N/A | ||||||||||
| 4000S Quattro | |||||||||||
| Front | |||||||||||
| Caster (Degrees) | (2) +1 +/- 2 | ||||||||||
| Camber (Degrees) | -1/4 to -1 1/4 | ||||||||||
| Toe-in (Inches) | (1) 0 to 1/3 | ||||||||||
| Toe-Out on Turns (Degrees) | |||||||||||
| Inner | 21 | ||||||||||
| Outer | 20 | ||||||||||
| Rear | |||||||||||
| Caster (Degrees) | N/A | ||||||||||
| Camber (Degrees) | -1/2 +/- 1/2 | ||||||||||
| Toe-in (Inches) | (1) +1/12 +/- 1/2 | ||||||||||
| Toe-Out on Turns (Degrees) | |||||||||||
| Inner | N/A | ||||||||||
| Outer | N/A | ||||||||||
| 5000S | |||||||||||
| Front | |||||||||||
| Caster (Degrees) | (2) -1/6 to 1 1/2 | ||||||||||
| Camber (Degrees) | -1 to 0 | ||||||||||
| Toe-in (Inches) | (1) Out 1/6 to In 1/12 | ||||||||||
| Toe-Out on Turns (Degrees) | |||||||||||
| Inner | 18 1/3 | ||||||||||
| Outer | 20 | ||||||||||
| Rear | |||||||||||
| Caster (Degrees) | (2) | ||||||||||
| Camber (Degrees) | (2) -5/6 to 1/6 | ||||||||||
| Toe-in (Inches) | (3) +1/12 to 5/12 | ||||||||||
| Toe-Out on Turns (Degrees) | |||||||||||
| Inner | N/A | ||||||||||
| Outer | N/A | ||||||||||
|
|||||||||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
