Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2018 Alfa Romeo Stelvio BaseFACTORY OEM SERVICE PROCEDURE
Module, Electronic Shift (ESM)
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| P0560-1C | SYSTEM VOLTAGE-CIRCUIT VOLTAGE OUT OF RANGE |
| P0562-16 | SYSTEM VOLTAGE LOW - CIRCUIT VOLTAGE BELOW THRESHOLD |
| P0563-17 | SYSTEM VOLTAGE HIGH - CIRCUIT VOLTAGE ABOVE THRESHOLD |
| P0606-42 | CONTROL MODULE PROCESSOR - GENERAL MEMORY FAILURE |
| P0607-48 | CONTROL MODULE PERFORMANCE - SUPERVISION SOFTWARE FAILURE |
| P0914-81 | GEAR SHIFT POSITION CIRCUIT - INVALID SERIAL DATA RECEIVED |
| P0919-81 | GEAR SHIFT POSITION CONTROL ERROR - INVALID SERIAL DATA RECEIVED |
| P1C72-09 | KNOB GEAR INDICATOR - COMPONENT FAILURES |
| P1C72-24 | KNOB GEAR INDICATOR - SIGNAL STUCK HIGH |
| P1C74-09 | KNOB BACKGROUND ILLUMINATION - COMPONENT FAILURES |
| P1C75-24 | KNOB PARK SWITCH - SIGNAL STUCK HIGH |
| P1C76-24 | KNOB RELEASE SWITCH - SIGNAL STUCK HIGH |
| P1C77-16 | KNOB SUPPLY VOLTAGE - CIRCUIT VOLTAGE BELOW THRESHOLD |
| P1C77-17 | KNOB SUPPLY VOLTAGE - CIRCUIT VOLTAGE ABOVE THRESHOLD |
| P1C78-16 | AUTORETURN SUPPLY VOLTAGE - CIRCUIT VOLTAGE BELOW THRESHOLD |
| P1C78-17 | AUTORETURN SUPPLY VOLTAGE - CIRCUIT VOLTAGE ABOVE THRESHOLD |
| P1C79-18 | AUTORETURN MOTOR - CIRCUIT CURRENT BELOW THRESHOLD |
| P1C79-19 | AUTORETURN MOTOR - CIRCUIT CURRENT ABOVE THRESHOLD |
| P1C7A-09 | AUTORETURN POSITION SENSOR - COMPONENT FAILURES |
| U0001-87 | AUTOMATIC GEARBOX SHIFTER MODULE (AGSM) CAN COMMUNICATION - MISSING MESSAGE |
| U0001-88 | AUTOMATIC GEARBOX SHIFTER MODULE (AGSM) CAN COMMUNICATION - BUS OFF |
| U0001-96 | AUTOMATIC GEARBOX SHIFTER MODULE (AGSM) CAN COMMUNICATION - COMPONENT INTERNAL FAILURE |
| U0101-87 | LOST COMMUNICATION WITH TRANSMISSION CONTROL MODULE - MISSING MESSAGE |
| U0140-87 | LOST COMMUNICATION WITH BODY CONTROL MODULE - MISSING MESSAGE |
| U0402-86 | INVALID DATA RECEIVED FROM TRANSMISSION CONTROL MODULE - SIGNAL INVALID |
| U0422-86 | INVALID DATA RECEIVED FROM BODY CONTROL MODULE - SIGNAL INVALID |
| U1301-49 | LOST COMMUNICATION WITH KNOB - INTERNAL ELECTRONIC FAILURE |
| U1302-49 | LOST COMMUNICATION WITH AUTORETURN - INTERNAL ELECTRONIC FAILURE |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.