Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
DTC U0127: Gauge Control Module Lost Communication With Keyless Access/TPMS Control Unit (V6, Gauge Control Module without CAN gateway)
| DTC Description | DTC |
|---|---|
| U0127 Gauge Control Module Lost Communication With Keyless Access/TPMS Control Unit |
DTC (Gauge Control Module)
NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information - Refer to: How to Troubleshoot the Fuel and Emissions Systems (L4), or How to Troubleshoot the Dual Clutch Transmission (DCT), or How to Troubleshoot the Brake Booster Pressure Monitoring System (With Auto Idle Stop System), or How to Troubleshoot the Fuel and Emissions Systems (V6, Without Auto Idle Stop System), or How to Troubleshoot the Fuel and Emissions Systems (V6, With Auto Idle Stop System) .
- Problem verification
-1. Clear the DTCs with the HDS.
- 2. Turn the vehicle to the OFF (LOCK) mode and then the ON mode.
- 3. Wait for at least 6 seconds.
- 4. Check for DTCs with the HDS.
DTC Description DTC U0127 Gauge Control Module Lost Communication With Keyless Access/TPMS Control Unit Is DTC U0127 indicated?
YES
Go to step 2.
NO
Intermittent failure, the system is OK at this time. Check for loose or poor connections.
- Fuse check
-1. Check the following fuse.
Fuse No. B10 (7.5 A) Location Under-dash fuse/relay box Is the fuse OK?
YES
Go to step 3.
NO
Replace the fuse. If the fuse blows again, repair a short to ground in the No. B10 (7.5 A) fuse circuit.
- Open wire check (IG1 VSA/ABS line)
-1. Turn the vehicle to the OFF (LOCK) mode.
- 2. Disconnect the following connectors.
Keyless access/TPMS control unit connector A (32P) Keyless access/TPMS control unit connector B (36P) Keyless access/TPMS control unit connector C (20P) - 3. Turn the vehicle to the ON mode.
- 4. Measure the voltage between test points 1 and 2.
Test condition Vehicle ON mode Keyless access/TPMS control unit connector A (32P): disconnected
Keyless access/TPMS control unit connector B (36P): disconnected
Keyless access/TPMS control unit connector C (20P): disconnected
Test point 1 Keyless access/TPMS control unit connector B (36P) No. 34 Test point 2 Body ground Is there battery voltage?
YES
The IG1 VSA/ABS wire is OK. Go to step 4.
NO
Repair an open or high resistance in the wire.
- Open wire check (GND lines)
-1. Turn the vehicle to the OFF (LOCK) mode
- 2. Check for continuity between test points 1 and 2.
Test condition Vehicle OFF (LOCK) mode Keyless access/TPMS control unit connector A (32P): disconnected
Keyless access/TPMS control unit connector B (36P): disconnected
Keyless access/TPMS control unit connector C (20P): disconnected
Test point 1 Keyless access/TPMS control unit connector A (32P) No. 17 Test point 2 Body ground Test point 1 Keyless access/TPMS control unit connector B (36P) No. 36 Test point 2 Body ground Is there continuity?
YES
The GND wires are OK. Go to step 5.
NO
Repair an open or high resistance in the ground wire or poor ground (G302).
- Open wire check (F-CAN A lines)
-1. Connect terminals A and B with a jumper wire.
Terminal A Keyless access/TPMS control unit connector C (20P) No. 2 Terminal B Keyless access/TPMS control unit connector C (20P) No. 12 - 2. Disconnect the following connector.
Gauge control module 32P connector - 3. Check for continuity between test points 1 and 2 respectively.
Test condition Vehicle OFF (LOCK) mode Keyless access/TPMS control unit connector A (32P): disconnected
Keyless access/TPMS control unit connector B (36P): disconnected
Keyless access/TPMS control unit connector C (20P): disconnected
Gauge control module 32P connector: disconnected
Test point 1 Gauge control module 32P connector No. 27 - Refer to: Gauge Control Module Input Test (2015-17), or Gauge Control Module Input Test (2018-19) Test point 2 Gauge control module 32P connector No. 28 - Refer to: Gauge Control Module Input Test (2015-17), or Gauge Control Module Input Test (2018-19) Is there continuity?
YES
The F-CAN A wires are OK. Replace the gauge control module .
NO
An open or poor connection in the F-CAN A wires between the keyless access/TPMS control unit and the gauge control module.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
No obligation. See pricing before you book.