Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
DLC Circuit Troubleshooting
- Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
- Connect the HDS to the DLC (see GENERAL TROUBLESHOOTING INFORMATION ).
- Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and read the HDS.
Does the HDS identify the vehicle?
YES - Go to step 4.
NO - Go to step 27.
- Check for Pending or Confirmed DTCs in the PGM-FI system with the HDS.
Are any Pending or Confirmed DTCs indicated?
YES - Go to the indicated DTC's troubleshooting. ■
NO -
- If the HDS does not communicate with the SRS, go to step 5.
- If the HDS does not communicate with the VSA system, go to step 7.
- If the HDS does not communicate with the EPS, go to step 9.
- If the HDS does not communicate with the SH-AWD system, go to step 11.
- If the HDS does not communicate with the TPMS, go to step 13.
- If the HDS does not communicate with the IMMOBI (immobilizer) system, go to step 15.
- If the HDS does not communicate with the ONE PUSH START system, go to step 17.
- If the HDS does not communicate with the BODY ELECTRICAL system, go to step 19.
- Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
- Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and watch the SRS indicator.
Does the SRS indicator come on and go off?
YES - Go to step 21.
NO - Go to the SRS general troubleshooting information (see GENERAL TROUBLESHOOTING INFORMATION ). ■
- Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
- Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and watch the VSA indicator.
Does the VSA indicator come on and go off?
YES - Go to step 21.
NO - Go to the symptom troubleshooting for ABS indicator, brake system indicator, VSA indicator do not go off (see ABS INDICATOR, BRAKE SYSTEM INDICATOR, AND VSA INDICATOR DO NOT GO OFF ). ■
- Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
- Start the engine, and watch the EPS indicator.
Does the EPS indicator come on and go off?
YES - Go to step 21.
NO - Go to the symptom troubleshooting for EPS indicator dose not go off, and no DTCs are stored (see EPS INDICATOR DOES NOT GO OFF, AND NO DTCS ARE STORED ). ■
- Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
- Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and watch the SH-AWD indicator.
Does the SH-AWD indicator come on and go off?
YES - Go to step 21.
NO - Go to the symptom troubleshooting for SH-AWD indicator dose not go off, and no DTCs are stored (see DTC 91-1: SH-AWD CONTROL UNIT PROGRAMMING ERROR ). ■
- Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
- Turn the ignition switch to ON (II), and watch the TPMS indicator.
Does the TPMS indicator come on and go off?
YES - Go to step 21.
NO - Go to the symptom troubleshooting for TPMS indicator dose not go off, and no DTCs are stored (see TPMS INDICATOR DOES NOT GO OFF, AND NO DTCS ARE STORED ). ■
- Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
- Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and watch the immobilizer indicator.
Does the immobilizer indicator stay on or flash?
YES - Go to the immobilizer system's troubleshooting; without keyless access (see SYMPTOM TROUBLESHOOTING INFORMATION ), with keyless access (see SYMPTOM TROUBLESHOOTING INFORMATION ). ■
NO - Go to step 21.
- Press the engine start/stop button to select the OFF mode.
- Press the engine start/stop button to select the ON mode, and watch the keyless access indicator.
Does the keyless access indicator stay on?
YES - Go to the keyless access system general troubleshooting information (see GENERAL TROUBLESHOOTING INFORMATION ). ■
NO - Go to step 21.
- Do the gauge self-diagnostic function (see SELF-DIAGNOSTIC FUNCTION ).
- Check the gauge display.
Is B-CAN- - ERROR indicated?
YES - Check for B-CAN system DTCs (see TROUBLESHOOTING - B-CAN SYSTEM DIAGNOSIS TEST MODE 1 AND TEST MODE 2 (WITHOUT THE HDS) ). ■
NO - Go to step 21.
- Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
- Disconnect the HDS from the DLC.
- Check for continuity between DLC terminal No. 7 and body ground (with keyless access; between body ground and DLC terminals No. 1 and No. 7 individually).
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES - Go to step 24.
NO - Go to step 25.
- Continue to check for continuity between DLC terminal No. 7 and body ground (with keyless access; between body ground and DLC terminals No. 1 and No. 7 individually), while disconnecting these connectors, one at a time:
- SRS unit A (39P)
- VSA modulator-control unit 47P
- EPS control unit D (28P)
- SH-AWD control unit A (20P) (with SH-AWD)
- TPMS control unit 20P
- Immobilizer-keyless control unit 7P (without keyless access)
- Audio unit A (24P) (without navigation)
- Audio-navigation unit A (24P) (with navigation)
- Driver's under-dash fuse/relay box Q (20P)
- Remote slot control unit 40P (with keyless access)
- Keyless access control unit B (32P) (with keyless access)
- Power control unit C (36P) (with keyless access)
Does continuity go away when one of the above connectors is disconnected?
YES - Replace the part that caused continuity go away when it was disconnected. ■
NO - Repair short in the wire between the DLC No. 7 (K-Line) and the VSA modulator-control unit, the EPS control unit, the SH-AWD control unit, the SRS unit, the TPMS control unit, the immobilizer-keyless control unit, the audio unit, the audio-navigation unit, the driver's under-dash fuse/relay box, the remote slot control unit, the keyless access control unit, or the DLC No. 1 (Diag-H line) and the power control unit (with keyless access). ■
- Connect DLC terminal No. 7 to body ground with a jumper wire (with keyless access system, also connect DLC terminal No. 1 to body ground with a jumper wire).
- Check for continuity between body ground and these connector terminals:
Connector Terminal SRS unit A (39P) No. 18 (LT BLU) VSA modulator-control unit 47P No. 10 (LT BLU) EPS control unit D (28P) No. 17 (LT BLU) SH-AWD control unit A (20P) (with SH-AWD) No. 5 (LT BLU) TPMS control unit 20P No. 7 (LT BLU) Immobilizer-keyless control unit 7P (without keyless access) No. 5 (LT BLU) Audio unit A (24P) (without navigation) No. 3 (LT BLU) Audio-navigation unit connector A (24P) (with navigation) No. 3 (LT BLU) Driver's under-dash fuse/relay box Q (20P) No. 16 (LT BLU) Remote slot control unit 40P (with keyless access) No. 34 (LT BLU) Keyless access control unit B (32P) (with keyless access) No. 4 (LT BLU) Power control unit C (36P) (with keyless access) No. 3 (GRY) Is there continuity between the body ground and each of the terminals in the chart?
YES - Replace the part that does not communicate with the HDS. ■
NO - Repair open in the wire between the DLC (K-Line or Diag-H) and the appropriate connector. ■
- Check for B-CAN system DTCs without the HDS (see
TROUBLESHOOTING - B-CAN SYSTEM DIAGNOSIS TEST MODE 1 AND TEST MODE 2 (WITHOUT THE HDS)
).
Is DTC U0029 and/or U0100 indicated?
YES - Go to step 38.
NO - Go to step 28.
- Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
- Disconnect the HDS from the DLC.
- Measure the voltage between DLC terminal No. 16 and body ground.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there battery voltage?
YES - Go to step 31.
NO - Repair open in the wire between DLC terminal No. 16 and the No. 15 BACK UP (10 A) fuse in the under-hood fuse/relay box. ■
- Measure the voltage between DLC terminals No. 4 and No. 16.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there battery voltage?
YES - Go to step 32.
NO - Repair open in the wire between DLC terminal No. 4 and body ground (G401 (see CONNECTOR TO FUSE/RELAY BOX INDEX )). ■
- Connect the HDS to the DLC (see GENERAL TROUBLESHOOTING INFORMATION ).
- Jump the SCS line with the HDS.
- Disconnect ECM/PCM connector A (49P).
- Disconnect the HDS from the DLC.
- Check for continuity between ECM/PCM connector terminal A48 and DLC terminal No. 6.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES - Go to step 37.
NO - Repair open in the wire between the ECM/PCM (A48) and DLC terminal No. 6. ■
- Check for continuity between ECM/PCM connector terminal A49 and DLC terminal No. 14.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES - Update the ECM/PCM if it does not have the latest software (see ECM/PCM Update ), or substitute a known-good ECM/PCM (see SUBSTITUTING THE ECM/PCM ), then recheck. If the symptom/indication goes away and the ECM/PCM was updated, troubleshooting is complete. If the symptom/indication goes away and the ECM/PCM was substituted, replace the original ECM/PCM (see ECM/PCM Replacement ). ■
NO - Repair open in the wire between the ECM/PCM (A49) and DLC terminal No. 14. ■
- Try to start the engine.
Does the engine start and idle?
YES - Go to the F-CAN circuit troubleshooting . ■
NO -
- If the starter does not crank, go to step 39.
- If the starter cranks, turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode; and go to step 41.
- Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
- Check the No. 3-1 IG MAIN (50 A) fuse in the under-hood fuse/relay box.
Is the fuse OK?
YES - Repair open in the wire between the No. 3-1 IG MAIN (50 A) fuse and the ignition switch (without keyless access) or power control unit (with keyless access). If the wire is OK, go to step 41.
NO - Repair short in the wire between the No. 3-1 IG MAIN (50 A) fuse and the ignition switch (without keyless access) or power control unit (with keyless access). Also replace the No. 3-1 IG MAIN (50 A) fuse. ■
- Inspect the No. 17 Fl MAIN (15 A) fuse in the under-hood fuse/relay box.
Is the fuse OK?
YES - Go to step 48.
NO - Go to step 42.
- Remove the blown No. 17 Fl MAIN (15 A) fuse from the under-hood fuse/relay box.
- Remove PGM-FI main relay 1 (A) from the under-hood fuse/relay box.
- Check for continuity between body ground and PGM-FI main relay 1 4P connector terminals No. 1 and No. 4 individually.Fig 8: Checking Continuity Between Body Ground And PGM-FI Main Relay 1 4P Connector Terminals No. 1 And No. 4
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES - Replace the under-hood fuse/relay box (see REMOVAL AND INSTALLATION ). Also replace the No. 17 Fl MAIN (15 A) fuse. ■
NO - Go to step 45.
- While disconnecting each of the parts or connectors below, one at a time, check for continuity between PGM-FI main relay 1 4P connector terminal No. 2 and body ground:
- PGM-FI main relay 2
- ECM/PCM connector B (49P)
- Each injector 2P connector
- CMP sensor 3P connector
- CKP sensor 3P connector
- MAF sensor/IAT sensor 5P connector
- Electronic throttle control system (ETCS) control relay
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Does continuity go away when one of the above parts or connectors is disconnected?
YES - Replace the part that made the short to body ground go away when disconnected. If the part is the ECM/PCM, update the ECM/PCM if it does not have the latest software (see ECM/PCM Update ), or substitute a known-good ECM/PCM (see SUBSTITUTING THE ECM/PCM ), then recheck. If the symptom/indication goes away and the ECM/PCM was updated, troubleshooting is complete. If the symptom/indication goes away and the ECM/PCM was substituted, replace the original ECM/PCM (see ECM/PCM Replacement ). Also replace the No. 17 Fl MAIN (15 A) fuse. ■
NO - Go to step 46.
- Disconnect the connectors from these components:
- PGM-FI main relay 2
- ECM/PCM connector B (49P)
- Injectors
- CMP sensor
- CKP sensor
- MAF sensor/IAT sensor
- Electronic throttle control system (ETCS) control relay
- Check for continuity between PGM-FI main relay 1 4P connector terminal No. 2 and body ground.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES - Repair short in the wire between PGM-FI main relay 1 and each part. Also replace the No. 17 Fl MAIN (15A)fuse. ■
NO - Replace PGM-FI main relay 1. Also replace the No. 17 FI MAIN (15A)fuse. ■
- Inspect the No. 9 FUEL PUMP (20 A) fuse in the driver's under-dash fuse/relay box.
Is the fuse OK?
YES - Go to step 60.
NO - Go to step 49.
- Remove the blown No. 9 FUEL PUMP (20 A) fuse from the driver's under-dash fuse/relay box.
- Remove the driver's dashboard undercover (see DRIVER'S DASHBOARD UNDERCOVER REMOVAL/INSTALLATION ), then remove PGM-FI main relay 2 (A) from the driver's under-dash fuse/relay box.
- Test PGM-FI main relay 2 (see
POWER RELAY TEST
).
Is the relay OK?
YES - Go to step 52.
NO - Replace PGM-FI main relay 2. Also replace the No. 9 FUEL PUMP (20 A) fuse. ■
- Check for continuity between PGM-FI main relay 2 4P connector terminal No. 2 and body ground.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES - Go to step 53.
NO - Go to step 56.
- Jump the SCS line with the HDS.
- Disconnect ECM/PCM connector B (49P).
- Check for continuity between ECM/PCM connector terminal B42 and body ground.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES - Repair short in the wire between the No. 9 FUEL PUMP (20 A) fuse and the ECM/PCM (B42), between the No. 9 FUEL PUMP (20 A) fuse and PGM-FI main relay 2, or between the No. 9 FUEL PUMP (20 A) fuse and the immobilizer control unit. Also replace the No. 9 FUEL PUMP (20 A) fuse. ■
NO - Replace the No. 9 FUEL PUMP (20 A) fuse, and update the ECM/PCM if it does not have the latest software (see ECM/PCM Update ), or substitute a known-good ECM/PCM (see SUBSTITUTING THE ECM/PCM ), then recheck. If the symptom/indication goes away and the ECM/PCM was updated, troubleshooting is complete. If the symptom/indication goes away and the ECM/PCM was substituted, replace the original ECM/PCM (see ECM/PCM Replacement ). ■
- Remove the rear seat cushion (see REAR SEAT REMOVAL/INSTALLATION ).
- Remove the access panel from the floor (see FUEL TANK UNIT REMOVAL AND INSTALLATION ).
- Disconnect the fuel pump 4P connector.
- Check for continuity between fuel pump 4P connector terminal No. 2 and body ground.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES - Repair short in the wire between the fuel pump and PGM-FI main relay 2. Also replace the No. 9 FUEL PUMP(20A)fuse. ■
NO - Check the fuel pump, and replace it if needed (see FUEL PUMP/FUEL GAUGE SENDING UNIT REPLACEMENT ). Also replace the No. 9 FUEL PUMP (20 A) fuse. ■
- Jump the SCS line with the HDS.
- Disconnect ECM/PCM connectors A (49P) and B (49P).
- Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode.
- Measure the voltage between ECM/PCM connector terminal B42 and body ground.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there battery voltage?
YES - Go to step 64.
NO - Repair open in the wire between the No. 9 FUEL PUMP (20 A) fuse and the ECM/PCM (B42). ■
- Measure the voltage between ECM/PCM connector terminal A6 and body ground.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there battery voltage?
YES - Go to step 69.
NO - Go to step 65.
- Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
- Remove PGM-FI main relay 1 (A) from the under-hood fuse/relay box.
- Measure the voltage between PGM-FI main relay 1 4P connector terminal No. 4 and body ground.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there battery voltage?
YES - Go to step 68.
NO - Replace the under-hood fuse/relay box (see REMOVAL AND INSTALLATION ). ■
- Check for continuity between PGM-FI main relay 1 4P connector terminal No. 3 and ECM/PCM connector terminal A6.Fig 19: Checking Continuity Between PGM-FI Main Relay 1 4P Connector Terminal No. 3 And ECM/PCM Connector
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES - Test PGM-FI main relay 1 (see POWER RELAY TEST ). If the relay is OK, update the ECM/PCM if it does not have the latest software (see ECM/PCM Update ), or substitute a known-good ECM/PCM (see SUBSTITUTING THE ECM/PCM ), then recheck. If the symptom/indication goes away and the ECM/PCM was updated, troubleshooting is complete. If the symptom/indication goes away and the ECM/PCM was substituted, replace the original ECM/PCM (see ECM/PCM Replacement ). ■
NO - Repair open in the wire between the ECM/PCM (A6) and PGM-FI main relay 1. ■
- Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
- Remove PGM-FI main relay 1 (A) from the under-hood fuse/relay box.
- Measure the voltage between PGM-FI main relay 1 4P connector terminal No. 1 and body ground.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there battery voltage?
YES - Go to step 72.
NO - Replace the under-hood fuse/relay box (see REMOVAL AND INSTALLATION ). ■
- Check for continuity between PGM-FI main relay 1 4P connector terminal No. 2 and ECM/PCM connector terminal B3.Fig 22: Checking Continuity Between PGM-FI Main Relay 1 4P Connector Terminal No. 2 And ECM/PCM Connector
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES - Go to step 73.
NO - Repair open in the wire between the ECM/PCM (B3) and PGM-FI main relay 1. ■
- Test PGM-FI main relay 1 (see
POWER RELAY TEST
).
Is PGM-FI main relay 1 OK?
YES - Go to step 74.
NO - Replace PGM-FI main relay 1. ■
- Disconnect ECM/PCM connectors A (49P), B (49P), and C (49P).
- Check for continuity between body ground and
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
