Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
DTC B12F2: Power Control Unit Lost Communication With Keyless Access Control Unit
- Make sure the remote is not in the remote slot.
- Clear the DTCs with the HDS.
- Do this procedure 10 times: Press the engine start/stop button to select the OFF, ACC, ON, and OFF mode.
- Check for DTCs with the HDS.
Is DTC B12F2 indicated?
YES -Go to step 5.
NO -Intermittent failure, the system is OK at this time. Check for loose or poor connections.
- Select ONE-PUSH START from the system select menu with the HDS.
- Select the KEYLESS ACCESS CONTROL UNIT and check for DTCs with the HDS.
Are any DTCs indicated?
YES -Go to the INDICATED DTC'S TROUBLESHOOTING .
NO -Go to step 7.
- Press the engine start/stop button to select the OFF mode.
- Disconnect power control unit connector C (36P).
- Disconnect the remote slot control unit 40P connector.
- Disconnect the electric steering lock 12P connector.
- Disconnect keyless access control unit connector B (32P).
- Check for continuity between body ground and power control unit connector C (36P) terminal No. 2.Fig 1: Checking Continuity Between Body Ground And Power Control Unit Connector C (36P) Terminal No. 2
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES -Repair a short to ground in the wire.
NO -Go to step 13.
- Check for continuity between keyless access control unit connector B (32P) terminal No. 6 and power control unit connector C (36P) terminal No. 2.Fig 2: Checking Continuity Between Keyless Access Control Unit Connector B (32P) Terminal And Power Control Unit Connector C (36P) Terminal
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES -Go to step 14.
NO -Repair an open or high resistance in the wire.
- Reconnect these items:
- Power control unit connector C (36P).
- Remote slot control unit 40P connector.
- Electric steering lock 12P connector.
- Keyless access control unit connector B (32P).
- Do the battery terminal disconnect procedure (see BATTERY TERMINAL DISCONNECTION AND RECONNECTION ).
- Wait for at least 10 seconds to clear the DTCs.
- Do the battery terminal reconnection procedure (see BATTERY TERMINAL DISCONNECTION AND RECONNECTION ).
- Turn the keyless access system mode switch ON.
- If necessary, remove the remote from the remote slot.
- Press the engine start/stop button to select the ON mode, then select the OFF mode.
- Insert the remote into the remote slot.
- Press and hold the engine start/stop button to select the ON mode.
Does the mode change to ON?
YES -Go to step 23.
NO -Go to step 26.
- Clear the DTCs with the HDS.
- Press the engine start/stop button to select the OFF.
- Check for DTCs with the HDS.
Is DTC B12F2 indicated?
YES -Replace the keyless access control unit (see CONTROL UNIT INPUT TEST ).
NO -Intermittent failure, the system is OK at this time. Check for loose or poor connections.
- Connect the HDS to the data link connector.
- Select COMMUNICATION STATUS in the INSPECTION MENU with the HDS.
- Check the value of STATUS with ESL, STATUS with KEYLESS ACCESS CONTROL UNIT, and STATUS with SLOT with the HDS.COMMUNICATION STATUS
HDS Description Value Status with ESL MTR CUT1 (Cont) Status 1 MTR CUT2 (IG) Status 1 IG1 Input State of ESL 1 MTRCONT Status of ESL 1 ESL Motor Status 1 Switch D detection for Unlock Status 1 Switch C detection for Unlock Status 1 Switch B detection for Unlock Status 1 Status with KEYLESS ACCESS CONTROL UNIT FOR KEY Authentication Result 1 Status with SLOT FOR KEY Authentication Result 1 Are only values of status with KEYLESS ACCESS CONTROL UNIT 1?
YES -Replace the keyless access control unit (see CONTROL UNIT INPUT TEST ).
NO -Replace the power control unit (see POWER CONTROL UNIT ).
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
