Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSACURA2010TL FWD V6-3.5LREPAIR AND DIAGNOSISRELAYS AND MODULESRELAYS AND MODULES - BRAKES AND TRACTION CONTROLELECTRONIC BRAKE CONTROL MODULETECHNICAL SERVICE BULLETINSALL TECHNICAL SERVICE BULLETINSABS/TCS - VSA WARNING LAMP ON/NO DTC'S SET
2010 Acura TL FWD V6-3.5L
ABS/TCS - VSA Warning Lamp ON/No DTC's Set
2010 Acura TL FWD V6-3.5LSECTION ABS/TCS - VSA Warning Lamp ON/No DTC's Set
10-041
October 13, 2010
Applies To:
2010 TL SH-AWD M/T - ALL
VSA System Indicator Is On With No DTC Stored; MID Indicates CHECK HILL START ASSIST SYSTEM
SYMPTOM
The VSA system indicator comes on, the MID indicates CHECK HILL START ASSIST SYSTEM, no AcuraLink message displays that an indicator is on, and no DTCs are stored. The indicators go out after the engine is started.
PROBABLE CAUSE
The clutch pedal was repeatedly not released fully between 0-50 mph for three successive times while shifting, causing the VSA control unit to incorrectly judge a clutch switch malfunction and fail to store DTC 118 (clutch pedal position switch B).
CORRECTIVE ACTION
Update the VSA control unit software with the HDS then do the VSA sensor neutral position memorization.
SOFTWARE INFORMATION
HDS Software Version:
2.023.009 (OCT 2010) or later.
HDS Control Module (CM) Update:
Database Update 17-SEP-2010 or later.
NOTE:
To avoid an incorrect repair that would not be covered under warranty, use the software version listed above or a later version.
The updated VSA software program ID and P/N are shown below. If the HDS is loaded with the latest software, and it displays No Update Needed during the update, the software for this service bulletin is already installed.
WARRANTY CLAIM INFORMATION
The normal warranty applies.
Operation Number: 4135A1
Flat Rate Time: 0.3 hour
Failed Part: P/N 57114-TK5-A55
Defect Code: 03214
Symptom Code: 03205
Skill Level: Repair Technician
REPAIR PROCEDURE
1. Update the VSA control unit software with the HDS. Refer to Service Bulletin 01-026, Updating Control Units/Modules.
NOTE:
If error code SD or 50 occurs afler the update process is completed, follow the instructions on the HDS. Turn the ignition switch OFF then ON (II), and retry programming. If the update was successfully completed, the HDS will display "this vehicle does not need an update at this time."
2. Do the VSA Sensor Neutral Position Memorization with the HDS, and follow the screen prompts.
Disclaimer
October 13, 2010
Applies To:
2010 TL SH-AWD M/T - ALL
VSA System Indicator Is On With No DTC Stored; MID Indicates CHECK HILL START ASSIST SYSTEM
SYMPTOM
The VSA system indicator comes on, the MID indicates CHECK HILL START ASSIST SYSTEM, no AcuraLink message displays that an indicator is on, and no DTCs are stored. The indicators go out after the engine is started.
PROBABLE CAUSE
The clutch pedal was repeatedly not released fully between 0-50 mph for three successive times while shifting, causing the VSA control unit to incorrectly judge a clutch switch malfunction and fail to store DTC 118 (clutch pedal position switch B).
CORRECTIVE ACTION
Update the VSA control unit software with the HDS then do the VSA sensor neutral position memorization.
SOFTWARE INFORMATION
HDS Software Version:
2.023.009 (OCT 2010) or later.
HDS Control Module (CM) Update:
Database Update 17-SEP-2010 or later.
NOTE:
To avoid an incorrect repair that would not be covered under warranty, use the software version listed above or a later version.
The updated VSA software program ID and P/N are shown below. If the HDS is loaded with the latest software, and it displays No Update Needed during the update, the software for this service bulletin is already installed.
WARRANTY CLAIM INFORMATION
The normal warranty applies.
Operation Number: 4135A1
Flat Rate Time: 0.3 hour
Failed Part: P/N 57114-TK5-A55
Defect Code: 03214
Symptom Code: 03205
Skill Level: Repair Technician
REPAIR PROCEDURE
1. Update the VSA control unit software with the HDS. Refer to Service Bulletin 01-026, Updating Control Units/Modules.
NOTE:
If error code SD or 50 occurs afler the update process is completed, follow the instructions on the HDS. Turn the ignition switch OFF then ON (II), and retry programming. If the update was successfully completed, the HDS will display "this vehicle does not need an update at this time."
2. Do the VSA Sensor Neutral Position Memorization with the HDS, and follow the screen prompts.
Disclaimer
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.