Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2008 Acura TL V6-3.2LFACTORY OEM SERVICE PROCEDURE
Ignition Timing: Testing and Inspection
Ignition Timing Inspection
1. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC).
2. Turn the ignition switch ON (II).
3. Make sure the HDS communicates with the vehicle and the engine control module (ECM)/powertrain control module (PCM). If it doesn't communicate, troubleshoot the DLC circuit.
4. Check for DTCs. If a DTC is present, diagnose and repair the cause before inspecting the ignition timing.
5. Start the engine. Hold the engine speed at 3,000 rpm with no load (in the N or P position (A/T) or neutral (M/T)) until the radiator fan comes on, then let it idle.
6. Check the idle speed.
7. Jump the SCS line with the HDS.
8. Remove the right side engine compartment cover.
9. Connect the timing light to the No. 1 ignition coil harness.
10. Aim the light toward the pointer (A) on the timing belt cover. Check the ignition timing under a no load condition, (headlights, blower fan, rear window defogger, and air conditioner are turned off).
11. If the ignition timing differs from the specification, check the cam timing. If the cam timing is OK, update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck. If the system works properly, and the ECM/PCM was substituted, replace the original ECM/PCM.
12. Disconnect the HDS and the timing light.
13. Reinstall the right side engine compartment cover.
1. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC).
2. Turn the ignition switch ON (II).
3. Make sure the HDS communicates with the vehicle and the engine control module (ECM)/powertrain control module (PCM). If it doesn't communicate, troubleshoot the DLC circuit.
4. Check for DTCs. If a DTC is present, diagnose and repair the cause before inspecting the ignition timing.
5. Start the engine. Hold the engine speed at 3,000 rpm with no load (in the N or P position (A/T) or neutral (M/T)) until the radiator fan comes on, then let it idle.
6. Check the idle speed.
7. Jump the SCS line with the HDS.
8. Remove the right side engine compartment cover.
9. Connect the timing light to the No. 1 ignition coil harness.
10. Aim the light toward the pointer (A) on the timing belt cover. Check the ignition timing under a no load condition, (headlights, blower fan, rear window defogger, and air conditioner are turned off).
11. If the ignition timing differs from the specification, check the cam timing. If the cam timing is OK, update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck. If the system works properly, and the ECM/PCM was substituted, replace the original ECM/PCM.
12. Disconnect the HDS and the timing light.
13. Reinstall the right side engine compartment cover.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.