Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSACURA2008RL V6-3.5LREPAIR AND DIAGNOSISBODY AND FRAMELOCKSKEYLESS ENTRYTESTING AND INSPECTIONPROGRAMMING AND RELEARNING
2008 Acura RL V6-3.5L
Programming and Relearning
2008 Acura RL V6-3.5LSECTION Programming and Relearning
Remote Registration and Reprogramming for Keyless Access System and Immobilizer System
Keyless Access System
Registration by the HDS is necessary when:
- Any of the remotes (A) are replaced.
- All of the remotes (A) are replaced.
- A new remote (A) is added.
- New remotes (A) are added.
- The keyless access control unit (B) is replaced.
- The ignition switch control unit (C) is replaced.
- The imoes unit (D) is replaced.
- Deleting the registration of a lost remote(s).
- The PCM is replaced.
NOTE: The keyless access control unit can store up to six remotes.
Immobilizer System
Registration by the HDS is necessary when:
- A built-in key (A) is added or replaced.
- The immobilizer control unit-receiver (B) is replaced.
- The imoes unit (C) is replaced.
- The PCM is replaced.
NOTE: The immobilizer control unit-receiver can store up to six built-in keys.
Registration
1. Turn the ignition switch ON (II) with the built-in key.
2. Connect the HDS to the data link connector.
3. Select KEYLESS ACCESS or IMMOBILIZER (depending on the part replaced)* from the SYSTEM SELECT menu.
- : If registering the imoes unit, select IMMOBILIZER from the SYSTEM SELECT menu. (This is not necessary to register as a keyless access composed part.)
4. Enter the TEST MODE menu, then select the suitable menu from the HDS indications.
Keyless Access System
Registration by the HDS is necessary when:
- Any of the remotes (A) are replaced.
- All of the remotes (A) are replaced.
- A new remote (A) is added.
- New remotes (A) are added.
- The keyless access control unit (B) is replaced.
- The ignition switch control unit (C) is replaced.
- The imoes unit (D) is replaced.
- Deleting the registration of a lost remote(s).
- The PCM is replaced.
NOTE: The keyless access control unit can store up to six remotes.
Immobilizer System
Registration by the HDS is necessary when:
- A built-in key (A) is added or replaced.
- The immobilizer control unit-receiver (B) is replaced.
- The imoes unit (C) is replaced.
- The PCM is replaced.
NOTE: The immobilizer control unit-receiver can store up to six built-in keys.
Registration
1. Turn the ignition switch ON (II) with the built-in key.
2. Connect the HDS to the data link connector.
3. Select KEYLESS ACCESS or IMMOBILIZER (depending on the part replaced)* from the SYSTEM SELECT menu.
- : If registering the imoes unit, select IMMOBILIZER from the SYSTEM SELECT menu. (This is not necessary to register as a keyless access composed part.)
4. Enter the TEST MODE menu, then select the suitable menu from the HDS indications.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.