2007 Acura TL BaseFACTORY OEM SERVICE PROCEDURE

Ignition Coil Relay Circuit Troubleshooting

  1. Check the No. 2 (15 A) fuse in the under-dash fuse/ relay box.

    Is the fuse OK? 

    YES  -Reinstall the fuse, then go to step 2.

    NO  -Replace the fuse. If the fuse continues to blow, locate and repair the short in the circuit between the under-dash fuse/relay box and the ignition coils.

  2. Remove the ignition coil relay from the under-dash fuse/relay box, and test it (see POWER RELAY TEST ).

    Is the relay OK? 

    YES  -Go to step 3.

    NO  -Replace the ignition coil relay.

  3. Measure the voltage between ignition coil relay 4P socket terminal No. 1 and body ground, then terminal No. 4 and body ground.
    Fig 1: Measuring Voltage Between Ignition Coil Relay 4P Socket Terminal No. 1 And Body Ground
    G05457441Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    YES  -Go to step 4.

    NO  -Replace the under-dash fuse/relay box.

  4. Check for continuity between ignition coil relay 4P socket terminal No. 2 and the each ignition coil 3P connector terminal No. 3.
    Fig 2: Checking Continuity Between Ignition Coil Relay 4P Socket Terminal No. 2 And Ignition Coil 3P Connector Terminal No. 3
    G05457442Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  -Go to step 5.

    NO  -Repair open in the wire between ignition coil relay 4P socket terminal No. 2 and each ignition coil 3P connector terminal No. 3.

  5. Check for continuity between each ignition coil 3P connector terminal No. 2 and the body ground.
    Fig 3: Checking Continuity Between Ignition Coil 3P Connector Terminal No. 2 And Body Ground
    G05457443Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  -Go to step 6.

    NO  -Repair open in the wire between ignition coil 3P connector terminal No. 2 and the body ground.

  6. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC) (see step 2 in GENERAL TROUBLESHOOTING INFORMATION ).
  7. Turn the ignition switch ON (II).
  8. Make sure the HDS communicates with the vehicle and the engine control module (ECM)/powertrain control module (PCM). If it doesn't communicate, troubleshoot the DLC circuit (see DLC CIRCUIT TROUBLESHOOTING (PART 2) ).
  9. Jump the SCS line with the HDS, then turn the ignition switch OFF.
    NOTE: This step must be done to protect the ECM/PCM from damage.
  10. Disconnect ECM/PCM connector E (31P).
  11. Check for continuity between ignition coil relay 4P socket terminal No. 3 and body ground.
    Fig 4: Checking Continuity Between Ignition Coil Relay 4P Socket Terminal No. 3 And Body Ground
    G05457444Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  -Repair short in the wire between ignition coil relay 4P socket terminal No. 3 and the ECM/PCM (E5).

    NO  -Go to step 12.

  12. Check for continuity between ignition coil relay 4P socket terminal No. 3 and ECM/PCM connector terminal E5.
    Fig 5: Checking Continuity Between Ignition Coil Relay 4P Socket Terminal No. 3 And ECM/PCM Connector Terminal E5
    G05457445Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  -The system is OK at this time. Check for loose or poor connections at the ignition coil relay and the ECM/PCM (E5).

    NO  -Repair open in the wire between ignition coil relay 4P socket terminal No. 3 and the ECM/PCM (E5).

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.