Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2002 Acura MDX Base, BGHAFACTORY OEM SERVICE PROCEDURE
Engine Performance DTCS
ENGINE PERFORMANCE DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION
| DTC (MIL) | Description |
|---|---|
| P0107 | Manifold Absolute Pressure Sensor Circuit Low Voltage Input |
| P0108 | Manifold Absolute Pressure Sensor Circuit High Voltage Input |
| P0112 | Intake Air Temperature Sensor Circuit Low Voltage Input |
| P0113 | Intake Air Temperature Sensor Circuit High Voltage Input |
| P0116 | Engine Coolant Temperature Sensor Range/Performance Problem |
| P0117 | Engine Coolant Temperature Sensor Circuit Low Voltage Input |
| P0118 | Engine Coolant Temperature Sensor Circuit High Voltage Input |
| P0122 | Throttle Position Sensor Circuit Low Voltage Input |
| P0123 | Throttle Position Sensor Circuit High Voltage Input |
| P0128 | Cooling System Malfunction |
| P0131 | Primary Heated Oxygen Sensor Circuit Low Voltage |
| P0132 | Primary Heated Oxygen Sensor Circuit High Voltage |
| P0133 | Primary Heated Oxygen Sensor Circuit Slow Response |
| P0135 | Primary Heated Oxygen Sensor Heater Circuit Malfunction |
| P0137 | Secondary Heated Oxygen Sensor Circuit Low Voltage |
| P0138 | Secondary Heated Oxygen Sensor Circuit High Voltage |
| P0139 | Secondary Heated Oxygen Sensor Slow Response |
| P0141 | Secondary Heated Oxygen Sensor Heater Circuit Malfunction |
| P0171 | Fuel System Too Lean |
| P0172 | Fuel System Too Rich |
| P0300 | Random Misfire |
| P0301 | Cylinder No. 1 Misfire Detected |
| P0302 | Cylinder No. 2 Misfire Detected |
| P0303 | Cylinder No. 3 Misfire Detected |
| P0304 | Cylinder No. 4 Misfire Detected |
| P0305 | Cylinder No. 5 Misfire Detected |
| P0306 | Cylinder No. 6 Misfire Detected |
| P0325 | Knock Sensor Circuit Malfunction |
| P0335 | Crankshaft Position Sensor No Signal Input |
| P0336 | Crankshaft Position Sensor Intermittent Interruption |
| P0401 | Exhaust Gas Recirculation Insufficient Flow Detected |
| P0420 | Catalyst System Efficiency Below Threshold |
| P0451 | Fuel Tank Pressure Sensor Range/Performance Problem |
| P0452 | Fuel Tank Pressure Sensor Low Voltage |
| P0453 | Fuel Tank Pressure Sensor High Voltage |
| P0505 | Idle Control System Malfunction |
| P0720 | Countershaft Speed Sensor Circuit |
| P1107 | Barometric Pressure Sensor Circuit Low Voltage |
| P1108 | Barometric Pressure Sensor Circuit High Voltage |
| P1121 | Throttle Position Sensor Signal Lower Than Expected |
| P1122 | Throttle Position Sensor Signal Higher Than Expected |
| P1128 | Manifold Absolute Pressure Sensor Signal Lower Than Expected |
| P1129 | Manifold Absolute Pressure Sensor Signal Higher Than Expected |
| P1259 | Variable Valve Timing & Lift Electronic Control System Malfunction |
| P1297 | Electrical Load Detector Circuit Low Voltage |
| P1298 | Electrical Load Detector Circuit High Voltage |
| P1361 | Top Dead Center Sensor No. 1 Intermittent Interruption |
| P1362 | Top Dead Center Sensor No. 1 No Signal |
| P1366 | Top Dead Center Sensor No. 2 Intermittent Interruption |
| P1367 | Top Dead Center Sensor No. 2 No Signal |
| P1456 | Evaporative Emission Control System Leak Detected (Fuel Tank System) |
| P1457 | Evaporative Emission Control System Leak Detected (EVAP Control Canister System) |
| P1491 | Exhaust Gas Recirculation Valve Insufficient Lift Detected |
| P1498 | Exhaust Gas Recirculation Valve Lift Sensor High Voltage |
| P1519 | Idle Air Control Valve Circuit Malfunction |
| P1607 | Powertrain Control Module Internal Circuit Malfunction |
| P1676 | Frame-To-Powertrain Torque Down Request Signal Line Failure |
| P1678 | Frame-To-Powertrain Torque Down Request Signal Line Failure |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
