Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2002 Acura 3.2CL BaseFACTORY OEM SERVICE PROCEDURE
Diagnostic Trouble Code Definitions
DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION
| DTC (MIL) | Description | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| P0107 | Manifold Absolute Pressure Sensor Circuit Low Voltage Input | ||||||||||
| P0108 | Manifold Absolute Pressure Sensor Circuit High Voltage Input | ||||||||||
| P0112 | Intake Air Temperature Sensor Circuit Low Voltage Input | ||||||||||
| P0113 | Intake Air Temperature Sensor Circuit High Voltage Input | ||||||||||
| P0116 | Engine Coolant Temperature Sensor Range/Performance Problem | ||||||||||
| P0117 | Engine Coolant Temperature Sensor Circuit Low Voltage Input | ||||||||||
| P0118 | Engine Coolant Temperature Sensor Circuit High Voltage Input | ||||||||||
| P0122 | Throttle Position Sensor Circuit Low Voltage Input | ||||||||||
| P0123 | Throttle Position Sensor Circuit High Voltage Input | ||||||||||
| P0128 | Cooling System Malfunction | ||||||||||
| P0131 | Primary Heated Oxygen Sensor Circuit Low Voltage | ||||||||||
| P0132 | Primary Heated Oxygen Sensor Circuit High Voltage | ||||||||||
| P0133 | Primary Heated Oxygen Sensor Circuit Slow Response | ||||||||||
| P0135 | Primary Heated Oxygen Sensor Heater Circuit Malfunction | ||||||||||
| P0137 | Secondary Heated Oxygen Sensor Circuit Low Voltage | ||||||||||
| P0138 | Secondary Heated Oxygen Sensor Circuit High Voltage | ||||||||||
| P0139 | Secondary Heated Oxygen Sensor Slow Response | ||||||||||
| P0141 | Secondary Heated Oxygen Sensor Heater Circuit Malfunction | ||||||||||
| P0171 | Fuel System Too Lean | ||||||||||
| P0172 | Fuel System Too Rich | ||||||||||
| P0300 | Random Misfire | ||||||||||
| P0301 | Cylinder No. 1 Misfire Detected | ||||||||||
| P0302 | Cylinder No. 2 Misfire Detected | ||||||||||
| P0303 | Cylinder No. 3 Misfire Detected | ||||||||||
| P0304 | Cylinder No. 4 Misfire Detected | ||||||||||
| P0305 | Cylinder No. 5 Misfire Detected | ||||||||||
| P0306 | Cylinder No. 6 Misfire Detected | ||||||||||
| P0325 | Knock Sensor Circuit Malfunction | ||||||||||
| P0335 | Crankshaft Position Sensor No Signal Input | ||||||||||
| P0336 | Crankshaft Position Sensor Intermittent Interruption | ||||||||||
| P0401 | Exhaust Gas Recirculation Insufficient Flow Detected | ||||||||||
| P0420 | Catalyst System Efficiency Below Threshold | ||||||||||
| P0451 | Fuel Tank Pressure Sensor Range/Performance Problem | ||||||||||
| P0452 | Fuel Tank Pressure Sensor Low Voltage | ||||||||||
| P0453 | Fuel Tank Pressure Sensor High Voltage | ||||||||||
| P0505 | Idle Control System Malfunction | ||||||||||
| P0700 | (1) Automatic Transaxle | ||||||||||
| P0710 | (1) Automatic Transaxle | ||||||||||
| P0715 | (1) Automatic Transaxle | ||||||||||
| P0720 | Countershaft Speed Sensor Circuit | ||||||||||
| P0730 | (1) Automatic Transaxle | ||||||||||
| P0740 | (1) Automatic Transaxle | ||||||||||
| P0753 | (1) Automatic Transaxle | ||||||||||
| P0758 | (1) Automatic Transaxle | ||||||||||
| P0763 | (1) Automatic Transaxle | ||||||||||
| P0780 | (1) Automatic Transaxle | ||||||||||
| P1106 | Barometric Pressure Sensor Range/Performance Problem | ||||||||||
| P1107 | Barometric Pressure Sensor Circuit Low Voltage | ||||||||||
| P1108 | Barometric Pressure Sensor Circuit High Voltage | ||||||||||
| P1121 | Throttle Position Sensor Signal Lower Than Expected | ||||||||||
| P1122 | Throttle Position Sensor Signal Higher Than Expected | ||||||||||
| P1128 | Manifold Absolute Pressure Sensor Signal Lower Than Expected | ||||||||||
| P1129 | Manifold Absolute Pressure Sensor Signal Higher Than Expected | ||||||||||
| P1259 | Variable Valve Timing & Lift Electronic Control System Malfunction | ||||||||||
| P1297 | Electrical Load Detector Circuit Low Voltage | ||||||||||
| P1298 | Electrical Load Detector Circuit High Voltage | ||||||||||
| P1361 | Top Dead Center Sensor No. 1 Intermittent Interruption | ||||||||||
| P1362 | Top Dead Center Sensor No. 1 No Signal | ||||||||||
| P1366 | Top Dead Center Sensor No. 2 Intermittent Interruption | ||||||||||
| P1367 | Top Dead Center Sensor No. 2 No Signal | ||||||||||
| P1456 | Evaporative Emission Control System Leak Detected (Fuel Tank System) | ||||||||||
| P1457 | Evaporative Emission Control System Leak Detected (EVAP Control Canister System) | ||||||||||
| P1491 | Exhaust Gas Recirculation Valve Insufficient Lift Detected | ||||||||||
| P1498 | Exhaust Gas Recirculation Valve Lift Sensor High Voltage | ||||||||||
| P1519 | Idle Air Control Valve Circuit Malfunction | ||||||||||
| P1607 | Powertrain Control Module Internal Circuit Malfunction | ||||||||||
| P1656 (2) | (1) Automatic Transaxle | ||||||||||
| P1676 (3)(4) | Frame-To-Powertrain Torque Down Request Signal Line Failure | ||||||||||
| P1678 (3)(4) | Frame-To-Powertrain Torque Down Request Signal Line Failure | ||||||||||
| P1705 | (1) Automatic Transaxle | ||||||||||
| P1706 | (1) Automatic Transaxle | ||||||||||
| P1709 (3) | (1) Automatic Transaxle | ||||||||||
| P1710 | (1) Automatic Transaxle | ||||||||||
| P1713 (3)(4) | (1) Automatic Transaxle | ||||||||||
| P1738 (3)(4) | (1) Automatic Transaxle | ||||||||||
| P1739 | (1) Automatic Transaxle | ||||||||||
| P1740 | (1) Automatic Transaxle | ||||||||||
| P1750 (5) | (1) Mechanical Problem In Hydraulic System | ||||||||||
| P1751 (5) | (1) Mechanical Problem In Hydraulic System | ||||||||||
| P1753 | (1) Automatic Transaxle | ||||||||||
| P1768 | (1) Automatic Transaxle | ||||||||||
| P1773 | (1) Automatic Transaxle | ||||||||||
| P1778 | (1) Automatic Transaxle | ||||||||||
|
|||||||||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.
